EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-TI2FA3842

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-TI2FA3842 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-TI2FA3842 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1553 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
USB
Students who are interested in USB, please pay attention....
wen06990234 Embedded System
Solution
How to test the passband of audio amplifier circuits?...
strawberry Analog electronics
【TI mmWave Radar Review】XWR14XX Data Path
[i=s]This post was last edited by a736015 on 2019-12-9 10:35[/i]IWR1443BOOST unboxing test: https://bbs.eeworld.com.cn/thread-1101610-1-1.html SDK and example download: https://bbs.eeworld.com.cn/thre...
a736015 TI Technology Forum
[I contribute to the Xilinx Resource Center] Development system and design process of "XILINX digital system field integration technology"
Development system and design process of "XILINX digital system field integration technology"...
wanghongyang FPGA/CPLD
SD card reading and writing problem! Thank you
I used two identical boards, the same SD card, and the same Windows system; but different problems occurred when reading and writing: On board A, reading and writing were normal; on board B, reading w...
2042 Embedded System
Please take a look at my assembly program, which I intend to embed in C language.
The hardware platform is C8051F120. The purpose of this program is to add 1 to the array number corresponding to the input value of P1 and P2. P1 and P2 are 12-bit numbers. The input pins are speciall...
pbabca 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2781  793  453  257  778  56  16  10  6  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号