A22L-DW-6A-10M datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> A22L-DW-6A-10M

A22L-DW-6A-10M: DescriptionPushbutton Switch, SPST, Momentary, Screw Terminal, Panel Mount; CategoryMechanical and electronic products switch; File Size224KB，13 Pages; ManufacturerOMRON; Websitehttps://www.omron.com

Download Datasheet Parametric View All

A22L-DW-6A-10M Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	A22L-DW-6A-10M	-	-	View	Buy Now

A22L-DW-6A-10M Overview

Pushbutton Switch, SPST, Momentary, Screw Terminal, Panel Mount

A22L-DW-6A-10M Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator type	SQUARE/FULL-GUARD TYPE
body width	30 mm
body height	54.7 mm
Body length or diameter	36 mm
Maximum contact voltage (AC)	6 V
Electrical life	500000 Cycle(s)
Manufacturer's serial number	A22
Installation features	PANEL MOUNT
Maximum operating temperature	55 °C
Minimum operating temperature	-20 °C
seal	IP65
surface mount	NO
Switch action	MOMENTARY
switch function	SPST
Switch type	PUSHBUTTON SWITCH
Termination type	SCREW
Base Number Matches	1

Preview

Download Datasheet

View All

Pushbutton Switch

Install in 22-dia. or 25-dia. Panel Cutout

Easy mounting and removal of Switch Unit.

Increase wiring efficiency with three-row mounting

of Switch Unit.

Finger protection mechanism on Switch Unit

provided as a standard feature.

Use 25-dia. ring to install in 25-dia. panel cutouts.

Install using either round, forked crimp terminals, or

ferrules.

Wide range of shapes and colors.

IP65 oil resistance (Non-lighted models)

EN60947-5-1

A22

This product was manufactured at OMRON Izumo. OMRON Izumo has obtained

approvals from international certification bodies for its quality system and environmental

control system.

Ordering Information

Construction

Operational Unit

•

Lock Fitting

Available Colors

Non-lighted:

Red, green, yellow, white, blue, black

Lighted:

Red, green yellow, white, blue

Lamp

•

Light Source

LED Lamp

Incandescent Lamp

Switch Unit

•

The above illustration shows a lighted model.

Contacts

SPST-NO, SPST-NC, SPST-NO + SPST-NC,

DPST-NO, DPST-NC

Lighting Method

Non-lighted

Lighted (without transformer)

Lighted (with transformer)

Refer to the pages 48 to 64 for specifications, accessories, installation, and precautions.

Recommended Resources

Crystal oscillator composed of DTL integrated circuit a

Interconnection circuit between external grid power supply and self-generated power supply

Class A FET amplifier power supply circuit diagram

Infrared remote control receiver with 60 commands

100Hz Wien bridge

Color TV remote control 13

Wireless Charging Technology: With the development of smart mobile devices, the public has higher and higher requirements for the power supply of mobile devices such as mobile phones. Therefore, wireless charging technology has at...; 木犯001号 Power technology

Hardware engineer interview questions: Analog Circuit 1. What is the content of Kirchhoff's theorem? (Shilan Microelectronics) 2. The formula of the plate capacitor (C=εS/4πkd). (Unknown) 3. The most basic one is the curve characteristic o...; limeiyue MCU

The video signal carrying capacity close to 1MHz is not enough. What op amp can I use to design a voltage follower?: As the title says, the video signal current output by the linear array CMOS is too small, and the input resistance of the AD module used is only 50ohm. I want to use an op amp to design a voltage foll...; XuYong虚庸 Analog electronics

How does STM32 make AD continuously sample and then delay 500MS before DA continuously outputs: This is my current graduation project: using the AD and DA built into the STM32F103ZET6 chip, the waveform is first continuously collected by the AD and stored in the external SRAM. After 500MS, the C...; wjg2954 stm32/stm8

Research on voice acquisition system and external communication interface based on DSP.pdf: Research on voice acquisition system and external communication interface based on DSP.pdf...; yunhuihe DSP and ARM Processors

Why are the upper and lower rows of pins not parallel when laying out AD devices?: When drawing a minimum system board for STM32, why do the four 2.54*10 pin headers on the top and bottom seem to be bent, wider on the left and narrower on the right?...; littleshrimp Talking

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components