The PGA-103+ provides excellent IP3 performance relative to device size and power
consumption. The combination of the design and E-PHEMT Structure provides en-
hanced linearity over a broad frequency range as evidence in the IP3 being typically 20
dB above the P 1dB point. This feature makes this amplifier ideal for use in:
• Driver amplifiers for complex waveform up converter paths
• Drivers in linearized transmit systems
• Secondary amplifiers in ultra High Dynamic range receivers
Unlike competing products, Mini-Circuits PGA-103+ provides Input and Output Return Loss
of 11-24 dB over 0.4-4 GHz without the need for any external matching components
A unique feature of the PGA-103+ which separates this design from all competitors is the
low noise figure performance in combination with the high dynamic range.
Ultra High IP3
Versus DC power Consumption:
45 dBm typical at 2 GHz at +5.0V
Supply Voltage and only 97mA
No External Matching Components
Required
Low Noise Figure:
0.6 dB up to 1.0 GHz
Notes:
a. Suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical
performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses.
b. The RFMD SPF-5189Z part number is used for identification and comparison purposes only.
Notes
A.
Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B.
Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C.
The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
www.minicircuits.com
P.O. Box 35166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Mini-Circuits
®
Page 1 of 5
Ultra Linear Low Noise
Monolithic Amplifier
Product Features
• 5V/3V operation
• High IP3, 45 dBm typ. at 2 GHz, Vd=5V
• Low Noise Figure, 0.6 at 1 GHz; 0.9 dB at 2 GHz
• Gain, 11.0 dB typ. at 2 GHz
• P1dB 22.5 dBm typ. at 2 GHz at Vd=5V
• No external matching components required
• May be used as a replacement for RFMD SPF-5189Z
a,b
0.05-4 GHz
CASE STYLE: DF782
PRICE: $1.99 ea. QTY. (20)
+RoHS Compliant
PGA-103+
Typical Applications
• Base station infrastructure
• Portable Wireless
• CATV & DBS
• MMDS & Wireless LAN
• LTE
The +Suffix identifies RoHS Compliance. See our web site
for RoHS Compliance methodologies and qualifications
General Description
PGA-103+ (RoHS compliant) is an advanced wideband amplifier fabricated using E-PHEMT technology
and offers extremely high dynamic range over a broad frequency range and with low noise figure. In
addition, the PGA-103+ has good input and output return loss over a broad frequency range without the
need for external matching components. Lead finish is SnAgNi. It has repeatable performance from lot to
lot and is enclosed in a SOT-89 package for very good thermal performance.
simplified schematic and pin description
3 RF-OUT & DC-IN
RF-IN
RF-OUT
and DC-IN
4
2 GROUND
1 RF-IN
GND
Function
RF IN
Pin Number
1
Description
RF input pin. This pin requires the use of an external DC blocking capacitor chosen for
the frequency of operation.
RF output and bias pin. DC voltage is present on this pin; therefore a DC blocking
capacitor is necessary for proper operation. An RF choke is needed to feed DC bias
without loss of RF signal due to the bias connection, as shown in “Recommended Ap-
plication Circuit”, Fig. 2
Connections to ground. Use via holes as shown in “Suggested Layout for PCB Design”
to reduce ground path inductance for best performance.
RF-OUT and DC-IN
3
GND
2,4
Notes:
a. Suitability for model replacement within a particular system must be determined by and is solely the responsibility of the customer based on, among other things, electrical
performance criteria, stimulus conditions, application, compatibility with other components and environmental conditions and stresses.
b. The RFMD SPF-5189Z part number is used for identification and comparison purposes only.
Notes
A.
Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B.
Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C.
The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
www.minicircuits.com
P.O. Box 35166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Mini-Circuits
®
REV. OR
M137349
PGA-103+
TH/RS/CP
131218
Page 2 of 5
Monolithic E-PHEMT MMIC Amplifier
Electrical Specifications
(1)
at 25°C, 50Ω, unless noted
Parameter
Frequency Range
Gain
PGA-103+
Vd=5V
Min.
0.05
Condition
(GHz)
0.05
0.4
1.0
2.0
3.0
4.0
Vd=3V
Max.
4.0
Typ.
26.5
22.1
Typ.
25.9
21.6
Units
GHz
dB
14.7
16.2
11.0
8.1
6.2
0.5
0.5
0.6
0.9
1.2
1.5
6.7
11.3
18.0
15.8
10.6
7.7
5.9
0.5
0.5
0.6
0.9
1.2
1.4
6.1
10.4
12.0
13.0
13.0
14.2
13.8
25.5
30.6
26.4
20.8
19.2
20.5
15.4
18.2
18.7
19.3
20.0
20.7
32.4
34.1
34.5
35.6
35.6
35.3
dBm
dB
dBm
dB
dB
dB
Noise Figure
0.05
0.4
1.0
2.0
3.0
4.0
Input Return Loss
0.05
0.4
1.0
2.0
3.0
4.0
10.0
13.0
12.8
13.7
15.0
14.1
23.8
Output Return Loss
0.05
0.4
1.0
2.0
3.0
4.0
10.0
21.8
20.6
17.2
16.0
21.2
20.0
21.5
22.5
22.5
22.9
23.2
36.7
39.0
41.9
Reverse Isolation
Output Power @1 dB compression
(2)
1.0
0.05
0.4
1.0
2.0
3.0
4.0
Output IP3
0.05
0.4
1.0
2.0
3.0
4.0
40.0
44.6
44.3
45.4
Device Operating Voltage
Device Operating Current
Device Current Variation vs. Temperature
Device Current Variation vs Voltage
Thermal Resitance
(1)
(2)
4.8
5.0
97
-178
0.014
36
5.2
120
3.0
60
-54
0.018
36
V
mA
μA/°C
mA/mV
°C/W
Measured on Mini-Circuits Characterization test board TB-313. See Characterization Test Circuit (Fig. 1)
Current increases at P1dB
DC Current Histogram, Vd=5V
Absolute Maximum Ratings
Parameter
Operating Temperature (ground lead)
Storage Temperature
Operating Current at 5.0V
Power Dissipation at 5.0V
Input Power (CW)
DC Voltage on Pin 3
Ratings
-40°C to 85°C
-65°C to 150°C
200 mA
1W
+21 dBm (50 to 2000 MHz)
+26 dBm (2000 to 4000 MHz)
6V
88-90
90-92
92-94
94-96
96-98
98-100
100-102
102-104
104-106
106-108
108-110
Note:
Permanent damage may occur if any of these limits are exceeded.
Electrical maximum ratings are not intended for continuous normal operation.
Current (mA)
Notes
A.
Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B.
Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C.
The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
www.minicircuits.com
P.O. Box 35166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Mini-Circuits
®
Page 3 of 5
Monolithic E-PHEMT MMIC Amplifier
Characterization Test Circuit
Vcc (Supply Voltage)
PGA-103+
RF-IN
BLK-18+
1
3
2,4
DUT
3/5V
Vd
Bias-Tee
ZX85-12G-S+
RF-OUT
TB-313
Fig 1.
Block Diagram of Test Circuit used for characterization. (DUT tested on Mini-Circuits Characterization test board TB-313)
Gain, Return loss, Output power at 1dB compression (P1 dB) , output IP3 (OIP3) and noise figure measured using Agilent’s N5242A
PNA-X microwave network analyzer.
Conditions:
1. Gain and Return loss: Pin= -25dBm
2. Output IP3 (OIP3): Two tones, spaced 1 MHz apart, 5 dBm/tone at output.
Recommended Application Circuit
Cblock=0.001μF, Bias-Tee=TCBT-14+, Cbypass=0.1μF
Fig 2a.
Evaluation board includes case, connectors and components
soldered to PCB
Fig 2b.
Evaluation board unconditionally stable (see note AN-60-064)
SEQ
A1
C1, C2
C3
C4
C5
D1
L1
L2
R2
Manufacturer P/N
PGA-103+
.01 uF
.01 uF
.01 uF
.01 pF
ESD Diode (see note 3)
TCCH-80+
620 nH
150 Ohm
Size
—
0805
1206
1206
0603
SOT 723
—
.115X.110
0603
Product Marking
P103
Notes
A.
Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B.
Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C.
The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
www.minicircuits.com
P.O. Box 35166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Mini-Circuits
®
Page 4 of 5
Monolithic E-PHEMT MMIC Amplifier
PGA-103+
Additional Detailed Technical Information
additional information is available on our dash board. To access this information
click here
Data Table
Performance Data
Swept Graphs
S-Parameter (S2P Files) Data Set
(.zip file)
Case Style
Tape & Reel
Standard quantities available on reel
DF782 (SOT 89)
Plastic package, exposed paddle
lead finish: tin-silver over nickel
F55
7” reels with 20, 50, 100, 200, 500 or 1K devices
Suggested Layout for PCB Design
Evaluation Board
Environmental Ratings
PL-313
TB-678-103+
TB-761-103+ (see Application Note AN-60-064)
ENV08T1
ESD Rating
Human Body Model (HBM): Class 1A (250 to <500V) in accordance with ANSI/ESD STM 5.1 - 2001
Machine Model (MM): Class M1(25V) in accordance with ANSI/ESD STM5.2-1999
Attention
Observe precautions
for handling electrostatic
sensitive devices
MSL Rating
Moisture Sensitivity: MSL1 in accordance with IPC/JEDEC J-STD-020D
MSL Test Flow Chart
Start
Visual
Inspection
Electrical Test
SAM Analysis
Reflow 3 cycles,
260°C
Soak
85°C/85RH
168 hours
Bake at 125°C,
24 hours
Visual
Inspection
Electrical Test
SAM Analysis
Notes
A.
Performance and quality attributes and conditions not expressly stated in this specification document are intended to be excluded and do not form a part of this specification document.
B.
Electrical specifications and performance data contained in this specification document are based on Mini-Circuit’s applicable established test performance criteria and measurement instructions.
C.
The parts covered by this specification document are subject to Mini-Circuits standard limited warranty and terms and conditions (collectively, “Standard Terms”); Purchasers of this part are entitled
to the rights and benefits contained therein. For a full statement of the Standard Terms and the exclusive rights and remedies thereunder, please visit Mini-Circuits’ website at www.minicircuits.com/MCLStore/terms.jsp
www.minicircuits.com
P.O. Box 35166, Brooklyn, NY 11235-0003 (718) 934-4500 sales@minicircuits.com
Packaging terminology analysis (from "PCB Terminology Manual" V1.0)1. BGA (ball grid array)is a spherical contact array, one of the surface mount packages. Spherical bumps are made on the back of the ...
[p=24, null, left][color=rgb(73, 73, 73)][font=微软雅黑]The choice of resistance value is still very important. In general design, the resistance value cannot be too large or too small. [/font][/color][/p...
[i=s]This post was last edited by mmmllb on 2015-2-9 17:28[/i] In recent days, some old posts have been pushed to the top. It may be that some new friends came across old posts and felt that they were...
I have a stm32 development board. I want to work on the file system recently, so I asked a friend to solder a k9f8g08 on it. I just started to look at the chip data of stm32 tonight, and found that it...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Among the uses of electrical energy, lighting accounts for a considerable proportion. Compared with the earlier ordinary incandescent lamps, the fluorescent lamps and energy-saving lamps we commonl...[Details]
Movpower is a portable power bank. It can charge most mobile phones and digital products, such as digital cameras, PDAs, and mobile phones such as Apple, iPod, Blackberry, Motorola, Samsung, Nokia,...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
Designing low power circuits while achieving acceptable performance is a difficult task. Doing so in
the RF
bands increases the challenge dramatically. Today, nearly everything has wireless...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
Synchronous buck designs are becoming increasingly difficult, and the selection of suitable ICs is becoming quite narrow. This Design Idea combines a current-mode PWM IC used in a flyback regulator...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
1. Basic principles of organic/polymer solar cells
The basic principle of organic/polymer solar cells is to use the photovoltaic effect generated by light incident on the heterojunction of sem...[Details]
At present, products in the field of monitoring generally focus on the field level, that is, the client/server (C/S) model is adopted, the purpose of which is to ensure the stability and reliability o...[Details]
1. Introduction
Due to the good programmability and superior performance of FPGA, the number of embedded systems using FPGA chips in LCD splicing screens is increasing rapidly, especially in t...[Details]
Talking about work
京公网安备 11010802033920号
EEWORLD
