EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SI2SA3162

Description
Transponder, SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-SI2SA3162 Overview

Transponder, SC/UPC Connector,

PH1-SI2SA3162 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253, OC-192, SONET
Connection TypeSC/UPC CONNECTOR
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1540 nm
Nominal optical power output1.122 mW
minimum return loss-27 dB
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
I am developing a single chip control board with RS232 communication
[img]3[/img]This board has 8 opto-isolated inputs, 7 small relay outputs, I2C memory, 2 AD inputs, 7-bit digital tube display (can be connected to a 128*64 LCD display), 1 buzzer, and can be connected...
xingmiao Industrial Control Electronics
Selection of external memory for DSP
In order to ensure the running speed of DSP, the external memory needs to have a certain speed, otherwise the DSP needs to add a waiting cycle when accessing the external memory.1) For C2000 series: C...
灞波儿奔 DSP and ARM Processors
How can I simulate the signal receiving process of the 125KHZ card reader/writer circuit?
How can I simulate the signal receiving process of the 125KHZ card reader/writer module circuit? The circuit is shown in the figure below. Is there a simulation signal source to add signal to the ante...
深圳小花 MCU
[Copter_accessory_DIY based on Renesas R7F0C80212] (II) Hardware platform construction and software framework design
2014-9-13 This week's progress is OK. The software framework has been built. The design is as follows: Use the concept of scheduler to design the system, establish 4 tasks, and arrange the execution o...
tziang Renesas Electronics MCUs
How to connect FPGA to router module
Please help me, experts: Cry:, my question is this: How to connect FPGA to a module (RM04 module) with router mode and working in router mode through a network cable, that is, the FPGA needs to be ass...
派大星123 FPGA/CPLD
What is the content and format of the command frame transmitted from the Zigbee coordinator to the PC?
What is the content and format of the command frame transmitted from the Zigbee coordinator to the PC?...
lgdd0503 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1627  334  2723  1584  2446  33  7  55  32  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号