EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-PS2LA3801

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-PS2LA3801 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-PS2LA3801 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsGR-253
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1553 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Introduction and in-depth understanding of capacitors [HW information]
Huawei document, a document recommended by many netizens...
wstt Discrete Device
【Book Collection】6502 microprocessor and its application
[b] Contents:[/b] 6502 Microprocessor Overview 6502 Microprocessor Internal Structure 6502 Timing Chapter 1 MPU 6502 Addressing Mode and Instruction System Chapter 2 6502 Assembly Language Programming...
wzt MCU
Wince5.0 touch screen driver, variable assignment invalid problem
The os is wince5.0, using KernelIoControl to dynamically associate interrupts. There is a global variable volatile INT CalibrationState that indicates the calibration status. In the TouchPanelReadCali...
000juli Embedded System
32k crystal oscillator casing needs to be grounded? ?
Circuit diagram...
huang91 Microcontroller MCU
Failed to write to the registry when adjusting the backlight brightness
I am adjusting the brightness of the backlight and have written several functions, one for reading the registry, one for writing the registry, and one for setting the backlight brightness. The program...
zglnzhy Embedded System
Does ARM have an instruction to directly obtain the overflow bit?
The traditional way to judge whether a bit is 1/0 is if(varx == 0x01), which is slow, so I would like to ask if there is an assembly instruction to directly get the overflowed bit....
bigbat MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 348  2386  1498  1318  1866  7  49  31  27  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号