16 Mbit (x8) Multi-Purpose Flash Plus
SST39VF1681 / SST39VF1682
SST39VF1681 / 16822.7V 16Mb (x8) MPF+ memories
Preliminary Specifications
FEATURES:
• Organized as 2M x8
• Single Voltage Read and Write Operations
– 2.7-3.6V
• Superior Reliability
– Endurance: 100,000 Cycles (Typical)
– Greater than 100 years Data Retention
• Low Power Consumption (typical values at 5 MHz)
– Active Current: 9 mA (typical)
– Standby Current: 3 µA (typical)
– Auto Low Power Mode: 3 µA (typical)
• Hardware Block-Protection/WP# Input Pin
– Top Block-Protection (top 64 KByte)
for SST39VF1682
– Bottom Block-Protection (bottom 64 KByte)
for SST39VF1681
• Sector-Erase Capability
– Uniform 4 KByte sectors
• Block-Erase Capability
– Uniform 64 KByte blocks
• Chip-Erase Capability
• Erase-Suspend/Erase-Resume Capabilities
• Hardware Reset Pin (RST#)
• Security-ID Feature
– SST: 128 bits; User: 128 bits
• Fast Read Access Time:
– 70 ns
– 90 ns
• Latched Address and Data
• Fast Erase and Byte-Program:
– Sector-Erase Time: 18 ms (typical)
– Block-Erase Time: 18 ms (typical)
– Chip-Erase Time: 40 ms (typical)
– Byte-Program Time: 7 µs (typical)
• Automatic Write Timing
– Internal V
PP
Generation
• End-of-Write Detection
– Toggle Bits
– Data# Polling
• CMOS I/O Compatibility
• JEDEC Standard
– Flash EEPROM Pinouts and Command sets
• Packages Available
– 48-ball TFBGA (6mm x 8mm)
– 48-lead TSOP (12mm x 20mm)
PRODUCT DESCRIPTION
The SST39VF168x devices are 2M x8 CMOS Multi-Pur-
pose Flash Plus (MPF+) manufactured with SST’s propri-
etary, high performance CMOS SuperFlash technology.
The split-gate cell design and thick-oxide tunneling injec-
tor attain better reliability and manufacturability compared
with alternate approaches. The SST39VF168x write (Pro-
gram or Erase) with a 2.7-3.6V power supply. These
devices conform to JEDEC standard pinouts for x8 mem-
ories.
Featuring high performance Byte-Program, the
SST39VF168x devices provide a typical Byte-Program
time of 7 µsec. These devices use Toggle Bit or Data# Poll-
ing to indicate the completion of Program operation. To pro-
tect against inadvertent write, they have on-chip hardware
and Software Data Protection schemes. Designed, manu-
factured, and tested for a wide spectrum of applications,
these devices are offered with a guaranteed typical endur-
ance of 100,000 cycles. Data retention is rated at greater
than 100 years.
The SST39VF168x devices are suited for applications that
require convenient and economical updating of program,
configuration, or data memory. For all system applications,
©2003 Silicon Storage Technology, Inc.
S71243-03-000
11/03
1
they significantly improve performance and reliability, while
lowering power consumption. They inherently use less
energy during Erase and Program than alternative flash
technologies. The total energy consumed is a function of
the applied voltage, current, and time of application. Since
for any given voltage range, the SuperFlash technology
uses less current to program and has a shorter erase time,
the total energy consumed during any Erase or Program
operation is less than alternative flash technologies. These
devices also improve flexibility while lowering the cost for
program, data, and configuration storage applications.
The SuperFlash technology provides fixed Erase and Pro-
gram times, independent of the number of Erase/Program
cycles that have occurred. Therefore the system software
or hardware does not have to be modified or de-rated as is
necessary with alternative flash technologies, whose
Erase and Program times increase with accumulated
Erase/Program cycles.
To meet high density, surface mount requirements, the
SST39VF168x are offered in both 48-ball TFBGA and
48-lead TSOP packages. See Figures 1 and 2 for pin
assignments.
The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc.
MPF is a trademark of Silicon Storage Technology, Inc.
These specifications are subject to change without notice.
16 Mbit Multi-Purpose Flash Plus
SST39VF1681 / SST39VF1682
Preliminary Specifications
Device Operation
Commands are used to initiate the memory operation func-
tions of the device. Commands are written to the device
using standard microprocessor write sequences. A com-
mand is written by asserting WE# low while keeping CE#
low. The address bus is latched on the falling edge of WE#
or CE#, whichever occurs last. The data bus is latched on
the rising edge of WE# or CE#, whichever occurs first.
The SST39VF168x also have the
Auto Low Power
mode
which puts the device in a near standby mode after data
has been accessed with a valid Read operation. This
reduces the I
DD
active read current from typically 9 mA to
typically 3 µA. The Auto Low Power mode reduces the typi-
cal I
DD
active read current to the range of 2 mA/MHz of
Read cycle time. The device exits the Auto Low Power
mode with any address transition or control signal transition
used to initiate another Read cycle, with no access time
penalty. Note that the device does not enter Auto-Low
Power mode after power-up with CE# held steadily low,
until the first address transition or CE# is driven high.
commands issued during the internal Program operation
are ignored. During the command sequence, WP# should
be statically held high or low.
Sector/Block-Erase Operation
The Sector- (or Block-) Erase operation allows the system
to erase the device on a sector-by-sector (or block-by-
block) basis. The SST39VF168x offer both Sector-Erase
and Block-Erase mode. The sector architecture is based
on uniform sector size of 4 KByte. The Block-Erase mode
is based on uniform block size of 64 KByte. The Sector-
Erase operation is initiated by executing a six-byte com-
mand sequence with Sector-Erase command (50H) and
sector address (SA) in the last bus cycle. The Block-Erase
operation is initiated by executing a six-byte command
sequence with Block-Erase command (30H) and block
address (BA) in the last bus cycle. The sector or block
address is latched on the falling edge of the sixth WE#
pulse, while the command (30H or 50H) is latched on the
rising edge of the sixth WE# pulse. The internal Erase
operation begins after the sixth WE# pulse. The End-of-
Erase operation can be determined using either Data#
Polling or Toggle Bit methods. See Figures 9 and 10 for tim-
ing waveforms and Figure 23 for the flowchart. Any com-
mands issued during the Sector- or Block-Erase operation
are ignored. When WP# is low, any attempt to Sector-
(Block-) Erase the protected block will be ignored. During
the command sequence, WP# should be statically held
high or low.
Read
The Read operation of the SST39VF168x is controlled
by CE# and OE#, both have to be low for the system to
obtain data from the outputs. CE# is used for device
selection. When CE# is high, the chip is deselected and
only standby power is consumed. OE# is the output con-
trol and is used to gate data from the output pins. The
data bus is in high impedance state when either CE# or
OE# is high. Refer to the Read cycle timing diagram for
further details (Figure 3).
Erase-Suspend/Erase-Resume Commands
The Erase-Suspend operation temporarily suspends a
Sector- or Block-Erase operation thus allowing data to be
read from any memory location, or program data into any
sector/block that is not suspended for an Erase operation.
The operation is executed by issuing one byte command
sequence with Erase-Suspend command (B0H). The
device automatically enters read mode typically within 20
µs after the Erase-Suspend command had been issued.
Valid data can be read from any sector or block that is not
suspended from an Erase operation. Reading at address
location within erase-suspended sectors/blocks will output
DQ
2
toggling and DQ
6
at “1”. While in Erase-Suspend
mode, a Byte-Program operation is allowed except for the
sector or block selected for Erase-Suspend.
To resume Sector-Erase or Block-Erase operation which has
been suspended the system must issue Erase Resume
command. The operation is executed by issuing one byte
command sequence with Erase Resume command (30H)
at any address in the last Byte sequence.
Byte-Program Operation
The SST39VF168x are programmed on a byte-by-byte
basis. Before programming, the sector where the byte
exists must be fully erased. The Program operation is
accomplished in three steps. The first step is the three-byte
load sequence for Software Data Protection. The second
step is to load byte address and byte data. During the Byte-
Program operation, the addresses are latched on the falling
edge of either CE# or WE#, whichever occurs last. The
data is latched on the rising edge of either CE# or WE#,
whichever occurs first. The third step is the internal Pro-
gram operation which is initiated after the rising edge of the
fourth WE# or CE#, whichever occurs first. The Program
operation, once initiated, will be completed within 10 µs.
See Figures 4 and 5 for WE# and CE# controlled Program
operation timing diagrams and Figure 19 for flowcharts.
During the Program operation, the only valid reads are
Data# Polling and Toggle Bit. During the internal Program
operation, the host is free to perform additional tasks. Any
©2003 Silicon Storage Technology, Inc.
S71243-03-000
11/03
2
16 Mbit Multi-Purpose Flash Plus
SST39VF1681 / SST39VF1682
Preliminary Specifications
Chip-Erase Operation
The SST39VF168x provide a Chip-Erase operation, which
allows the user to erase the entire memory array to the “1”
state. This is useful when the entire device must be quickly
erased.
The Chip-Erase operation is initiated by executing a six-
byte command sequence with Chip-Erase command
(10H) at address AAAH in the last byte sequence. The
Erase operation begins with the rising edge of the sixth
WE# or CE#, whichever occurs first. During the Erase
operation, the only valid read is Toggle Bit or Data# Polling.
See Table 6 for the command sequence, Figure 9 for tim-
ing diagram, and Figure 23 for the flowchart. Any com-
mands issued during the Chip-Erase operation are
ignored. When WP# is low, any attempt to Chip-Erase will
be ignored. During the command sequence, WP# should
be statically held high or low.
‘1’. The Data# Polling is valid after the rising edge of fourth
WE# (or CE#) pulse for Program operation. For Sector-,
Block- or Chip-Erase, the Data# Polling is valid after the
rising edge of sixth WE# (or CE#) pulse. See Figure 6 for
Data# Polling timing diagram and Figure 20 for a flowchart.
Toggle Bits (DQ6 and DQ2)
During the internal Program or Erase operation, any con-
secutive attempts to read DQ
6
will produce alternating “1”s
and “0”s, i.e., toggling between 1 and 0. When the internal
Program or Erase operation is completed, the DQ
6
bit will
stop toggling. The device is then ready for the next opera-
tion. For Sector-, Block-, or Chip-Erase, the toggle bit (DQ
6
)
is valid after the rising edge of sixth WE# (or CE#) pulse.
DQ
6
will be set to “1” if a Read operation is attempted on an
Erase-Suspended Sector/Block. If Program operation is ini-
tiated in a sector/block not selected in Erase-Suspend
mode, DQ
6
will toggle.
An additional Toggle Bit is available on DQ
2
, which can be
used in conjunction with DQ
6
to check whether a particular
sector is being actively erased or erase-suspended. Table 1
shows detailed status bits information. The Toggle Bit
(DQ
2
) is valid after the rising edge of the last WE# (or CE#)
pulse of Write operation. See Figure 7 for Toggle Bit timing
diagram and Figure 20 for a flowchart.
TABLE 1: W
RITE
O
PERATION
S
TATUS
Status
Normal
Standard
Operation Program
Standard
Erase
Erase-
Suspend
Mode
Read from
Erase Suspended
Sector/Block
Read from
Non- Erase Suspended
Sector/Block
Program
Write Operation Status Detection
The SST39VF168x provide two software means to detect
the completion of a Write (Program or Erase) cycle, in
order to optimize the system write cycle time. The software
detection includes two status bits: Data# Polling (DQ
7
) and
Toggle Bit (DQ
6
). The End-of-Write detection mode is
enabled after the rising edge of WE#, which initiates the
internal Program or Erase operation.
The actual completion of the nonvolatile write is asyn-
chronous with the system; therefore, either a Data# Poll-
ing or Toggle Bit read may be simultaneous with the
completion of the write cycle. If this occurs, the system
may possibly get an erroneous result, i.e., valid data may
appear to conflict with either DQ
7
or DQ
6
. In order to pre-
vent spurious rejection, if an erroneous result occurs, the
software routine should include a loop to read the
accessed location an additional two (2) times. If both
reads are valid, then the device has completed the Write
cycle, otherwise the rejection is valid.
DQ
7
DQ
7
#
0
1
DQ
6
Toggle
Toggle
1
DQ
2
No Toggle
Toggle
Toggle
Data
Data
Data
DQ
7
#
Toggle
N/A
T1.0 1243
Data# Polling (DQ
7
)
When the SST39VF168x are in the internal Program oper-
ation, any attempt to read DQ
7
will produce the comple-
ment of the true data. Once the Program operation is
completed, DQ
7
will produce true data. Note that even
though DQ
7
may have valid data immediately following the
completion of an internal Write operation, the remaining
data outputs may still be invalid: valid data on the entire
data bus will appear in subsequent successive Read
cycles after an interval of 1 µs. During internal Erase oper-
ation, any attempt to read DQ
7
will produce a ‘0’. Once the
internal Erase operation is completed, DQ
7
will produce a
©2003 Silicon Storage Technology, Inc.
Note:
DQ
7
and DQ
2
require a valid address when reading
status information.
S71243-03-000
11/03
3
16 Mbit Multi-Purpose Flash Plus
SST39VF1681 / SST39VF1682
Preliminary Specifications
Data Protection
The SST39VF168x provide both hardware and software
features to protect nonvolatile data from inadvertent writes.
Hardware Reset (RST#)
The RST# pin provides a hardware method of resetting the
device to read array data. When the RST# pin is held low
for at least T
RP,
any in-progress operation will terminate and
return to Read mode. When no internal Program/Erase
operation is in progress, a minimum period of T
RHR
is
required after RST# is driven high before a valid Read can
take place (see Figure 15).
The Erase or Program operation that has been interrupted
needs to be reinitiated after the device resumes normal
operation mode to ensure data integrity.
Hardware Data Protection
Noise/Glitch Protection: A WE# or CE# pulse of less than 5
ns will not initiate a write cycle.
V
DD
Power Up/Down Detection: The Write operation is
inhibited when V
DD
is less than 1.5V.
Write Inhibit Mode: Forcing OE# low, CE# high, or WE#
high will inhibit the Write operation. This prevents inadvert-
ent writes during power-up or power-down.
Software Data Protection (SDP)
The SST39VF168x provide the JEDEC approved Software
Data Protection scheme for all data alteration operations,
i.e., Program and Erase. Any Program operation requires
the inclusion of the three-byte sequence. The three-byte
load sequence is used to initiate the Program operation,
providing optimal protection from inadvertent Write opera-
tions, e.g., during the system power-up or power-down.
Any Erase operation requires the inclusion of six-byte
sequence. These devices are shipped with the Software
Data Protection permanently enabled. See Table 6 for the
specific software command codes. During SDP command
sequence, invalid commands will abort the device to Read
mode within T
RC.
Hardware Block Protection
The SST39VF1682 supports top hardware block protec-
tion, which protects the top 64 KByte block of the device.
The SST39VF1681 supports bottom hardware block pro-
tection, which protects the bottom 64 KByte block of the
device. The Boot Block address ranges are described in
Table 2. Program and Erase operations are prevented on
the 64 KByte when WP# is low. If WP# is left floating, it is
internally held high via a pull-up resistor, and the Boot
Block is unprotected, enabling Program and Erase opera-
tions on that block.
TABLE 2: B
OOT
B
LOCK
A
DDRESS
R
ANGES
Product
Bottom Boot Block
SST39VF1681
Top Boot Block
SST39VF1682
1F0000H-1FFFFFH
T2.1 1243
Address Range
000000H-00FFFFH
Common Flash Memory Interface (CFI)
The SST39VF168x also contain the CFI information to
describe the characteristics of the device. In order to enter
the CFI Query mode, the system must write three-byte
sequence, same as product ID entry command with 98H
(CFI Query command) to address AAAH in the last byte
sequence. Once the device enters the CFI Query mode, the
system can read CFI data at the addresses given in Tables
7 through 9. The system must write the CFI Exit command
to return to Read mode from the CFI Query mode.
©2003 Silicon Storage Technology, Inc.
S71243-03-000
11/03
4
16 Mbit Multi-Purpose Flash Plus
SST39VF1681 / SST39VF1682
Preliminary Specifications
Product Identification
The Product Identification mode identifies the devices as
the SST39VF1681 and SST39VF1682, and manufacturer
as SST. Users may use the software Product Identifica-
tion operation to identify the part (i.e., using the device ID)
when using multiple manufacturers in the same socket.
For details, see Table 6 for software operation, Figure 11
for the software ID Entry and Read timing diagram, and
Figure 21 for the software ID Entry command sequence
flowchart.
TABLE 3: P
RODUCT
I
DENTIFICATION
Address
Manufacturer’s ID
Device ID
SST39VF1681
SST39VF1682
0001H
0001H
C8H
C9H
T3.1 1243
apparently causes the device to behave abnormally, e.g.,
not read correctly. Please note that the software ID Exit/CFI
Exit command is ignored during an internal Program or
Erase operation. See Table 6 for software command
codes, Figure 13 for timing waveform, and Figures 21 and
22 for flowcharts.
Security ID
The SST39VF168x devices offer a 256-bit Security ID
space which is divided into two 128-bit segments. The first
segment is programmed and locked at SST with a random
128-bit number. The user segment is left un-programmed
for the customer to program as desired.
To program the user segment of the Security ID, the user
must use the Security ID Byte-Program command. To
detect end-of-write for the SEC ID, read the toggle bits. Do
not use Data# Polling. Once this is complete, the Sec ID
should be locked using the User Sec ID Program Lock-Out.
This disables any future corruption of this space. Note that
regardless of whether or not the Sec ID is locked, neither
Sec ID segment can be erased.
The Security ID space can be queried by executing a
three-byte command sequence with Enter-Sec-ID com-
mand (88H) at address AAAH in the last byte sequence.
Execute the Exit-Sec-ID command to exit this mode. Refer
to Table 6 for more details.
Data
BFH
0000H
Product Identification Mode Exit/
CFI Mode Exit
In order to return to the standard Read mode, the Software
Product Identification mode must be exited. Exit is accom-
plished by issuing the software ID Exit command
sequence, which returns the device to the Read mode.
This command may also be used to reset the device to the
Read mode after any inadvertent transient condition that
F
UNCTIONAL
B
LOCK
D
IAGRAM
X-Decoder
SuperFlash
Memory
Memory Address
Address Buffer & Latches
Y-Decoder
CE#
OE#
WE#
WP#
RESET#
I/O Buffers and Data Latches
Control Logic
DQ7 - DQ0
1243 B1.0
©2003 Silicon Storage Technology, Inc.
S71243-03-000
11/03
5
京公网安备 11010802033920号
EEWORLD
