XC6123F336ER datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > XC6123F336ER

Preview

XC6123F336ER: DescriptionVoltage Detector with Watchdog Function and ON/OFF Control (VDF=1.6V~5.0V); File Size430KB，23 Pages; ManufacturerTOREX; Websitehttp://www.torex.co.jp/chinese/

Download Datasheet View All

XC6123F336ER Overview

Voltage Detector with Watchdog Function and ON/OFF Control (VDF=1.6V~5.0V)

Preview

Download Datasheet

View All

XC6121/XC6122

XC6123/XC6124

Series

■GENERAL

DESCRIPTION

ETR0209-009

Voltage Detector with Watchdog Function and ON/OFF Control (V

=1.6V~5.0V)

The XC6121/XC6122/XC6123/XC6124 series are groups of high-precision, low current consumption voltage detectors with

watchdog functions incorporating CMOS process technology. The series consist of a reference voltage source, delay circuit,

comparator, and output driver. With the built-in delay circuit, the XC6121/XC6122/XC6123/XC6124 series’ ICs do not require

any external components to output signals with release delay time. The output type is V

DFL

low when detected. With the

XC6121/XC6122/XC6123/XC6124 series’ ICs, the EN/ENB pin can control ON and OFF of the watchdog functions. By setting

the EN/ENB pin to low or high level, the watchdog function can be OFF while the voltage detector remains operation. Since

the EN/ENB pin of the XC6122 and XC6124 series is internally pulled up to the V

pin or pulled down to the V

pin, the ICs

can be used with the EN/ENB pin left open, when the watchdog functions is used. The detect voltages are internally fixed

1.6V ~ 5.0V in increments of 100mV, using laser trimming technology. Six watchdog timeout period settings are available in a

range from 50ms to 1.6s. Five release delay time settings are available in a range from 3.13ms to 400ms.

■APPLICATIONS

●Microprocessor

watchdog monitoring

and reset circuits

●Memory

battery backup circuits

●System

power-on reset circuits

●Power

failure detection

■FEATURES

Detect Voltage Range

Hysteresis Width

Operating Voltage Range

Detect Voltage Temperature

Characteristics

: +100ppm/

C (TYP.)

Output Configuration

: N-channel open drain

Watchdog Pin

: Watchdog input

If watchdog input maintains ‘H’

or ‘L’ within the watchdog

timeout period, a reset signal is

output from the RESETB pin.

EN/ENB Pin

: When the EN/ENB pin voltage is

set to low or high level, the

watchdog function is forced off.

Release Delay Time

: 400ms, 200ms, 100ms, 50ms,

3.13ms (TYP.)

Watchdog Timeout Period

: 1.6s, 800ms, 400ms, 200ms,

100ms, 50ms (TYP.)

Package

: SOT-25, USP-6C

: 1.6V ~ 5.0V, +2%

(100mV increments)

: V

DFL

x 5% (TYP.)

: 1.0V ~ 6.0V

■TYPICAL

APPLICATION CIRCUIT

■TYPICAL

PERFORMANCE

CHARACTERISTICS

●Supply

Current vs. Input Voltage

ＸＣ６１２１½ＸＣ６１２４(V

=２.７Ｖ）

14.0

Ta=85℃

(μA)

Supply Current:　I

12.0

10.0

8.0

6.0

4.0

2.0

Input Voltage:　V

(V)

Ta=25℃

Ta=-40℃

1/23

Recommended Resources

Emitter coupled flip-flop circuits and applications

JA1 type (1kVA) AC voltage regulator circuit

Household electroacupuncture device

Sonic remote control switch circuit diagram

555DGK—63L dual-function disinfection cabinet circuit

100kHz sine wave oscillator

Inverted Pendulum PID Reference Program: [i=s] This post was last edited by paulhyde on 2014-9-15 03:13 [/i] Inverted Pendulum PID Reference Program...; 低碳哥2 Electronics Design Contest

Why can't I find HEADER 47 when drawing a schematic using protel SE?: As title...; gaoli.85 Embedded System

Select components: Select components>> [media=x,500,375]http://v.youku.com/v_show/id_XNzkxOTUxMTI4.html[/media]...; 雨中 ADI Reference Circuit

STM32F407 485 communication problem: The 485 module on my board is connected to usart1, PB6 and PB7. I followed the 485 communication routine of the Atom development board and changed serial port 2 to serial port 1. I can communicate wit...; wk好好学习 stm32/stm8

Which chip in PIC18F is similar to PIC16F877A, so that the 877A program can be transplanted to it with slight modifications?: I would like to ask you guys, which chip in PIC18F is similar to PIC16F877A, so that I can port the 877A program to it with slight modifications?...; zhangqianqf Microchip MCU

Problems with calling OSQPost() in STM32 serial port interrupt program: When I call OSQPost() in the serial port interrupt program of STM32, I call OSQPend() in the task to wait for the message of the receiving queue. As a result, the received data is wrong. However, I ca...; jgphu_123 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components