Incorporates two enable inputs to simplify cascading and/or
data reception
1.2μ
CMOS
- Latchup immune
High speed
Low power consumption
Single 5 volt supply
Available QML Q or V processes
Flexible package
- 16-pin DIP
- 16-lead flatpack
UT54ACS139 - SMD 5962-96546
UT54ACTS139 - SMD 5962-96547
DESCRIPTION
The UT54ACS139 and the UT54ACTS139 are designed to be
used in high-performance memory-decoding or data-routing ap-
plications requiring very short propagation delay times.
The devices consist of two individual two-line to four-line de-
coders in a single package. The active-low enable input can be
used as a data line in demultiplexing applications.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
ENABLE
INPUTS
G
H
L
L
L
L
SELECT
INPUTS
B
X
L
L
H
H
A
X
L
H
L
H
Y0
H
L
H
H
H
OUTPUT
Y1
H
H
L
H
H
Y2
H
H
H
L
H
Y3
H
H
H
H
L
PINOUTS
16-Pin DIP
Top View
IG
1A
1B
1Y0
1Y1
1Y2
1Y3
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
16-Lead Flatpack
Top View
1G
1A
1B
1Y0
1Y1
1Y2
1Y3
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
LOGIC DIAGRAM
(4)
1G
(1)
(5)
(6)
SELECT
1A
1B
(2)
(3)
(7)
(12)
2G
(15)
(11)
(10)
SELECT
2A
2B
(14)
(13)
(9)
1Y0
1Y1
1Y2
DATA
1Y3
2Y0
2Y1
2Y2
2Y3
1
LOGIC SYMBOL
1A
1B
1G
(2)
(3)
(1)
X/Y
1
2
EN
0
1
2
3
(4)
(5)
(6)
(7)
(12)
(11)
(10)
(9)
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
1A
1B
1G
(2)
(3)
(1)
DMUX
0
1
0
G
---
3
0
1
2
3
(4)
(5)
(6)
(7)
(12)
(11)
(10)
(9)
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
2A
2B
2G
(14)
(13)
(15)
2A
2B
2G
(14)
(13)
(15)
Note:
1. Logic symbols in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
I
OS
P
total
I
DDQ
ΔI
DDQ
Short-circuit output current
2 ,4
ACTS/ACS
Power dissipation
2, 8, ,9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
V
O
= V
DD
and V
SS
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
-200
200
1.8
10
1.6
mA
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
8
.5V
DD
.7V
DD
-1
1
0.40
0.25
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
V
V
OH
V
I
OL
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
I am posting this today, preparing to start learning the Linux system. I was confused for a while, at least I encountered problems at the beginning, let alone the Linux system. Now I have sorted out t...
[i=s]This post was last edited by lugl4313820 on 2022-2-25 07:54[/i]I have previously used N32G45 to perform packet loss tests at various communication rates. Today, I will also perform a packet loss ...
Hello everyone, I am using sqlite database, but I found that it does not support Chinese paths, but I want to put the data on the memory card, how can I solve it? I found that it may be a problem with...
This video introduces a simple method to estimate the transient response of a power supply by understanding the control bandwidth and output filter capacitor characteristics. This method takes advanta...
If the resonant inductance of the primary side can be replaced by the leakage inductance of the transformer, then there is no need for an external inductor. How do we calculate the inductance paramete...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
Have you ever heard stories about "crazy appliances"? Think of microwaves that turn on automatically or ovens that preheat without any human input? With radios and electromagnetic interfaces ubiqui...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Learned the following information.
Customer product: industrial computer motherboard
Glue application area: CPU/BGA filling
Glue color requirements: black or t...[Details]
Recently, Joyson Electronics has made positive progress in the core technology research and development of the robot's "brain and brain" and key components, and launched the industry's first integr...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
Wearable technology is taking off, with applications evolving rapidly, from smartwatches to fitness trackers and even smart wigs! Bluetooth Smart is at the center of this revolution. This is the se...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
