The UT54ACS74 and the UT54ACTS74 contain two indepen-
dent D-type positive triggered flip-flops. A low level at the
Preset or Clear inputs sets or resets the outputs regardless of the
levels of the other inputs. When Preset and Clear are inactive
(high), data at the D input meeting the setup time requirement
is transferred to the outputs on the positive-going edge of the
clock pulse. Following the hold time interval, data at the D
input may be changed without affecting the levels at the outputs.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUTS
PRE
L
H
L
H
H
H
CLR
H
L
L
H
H
H
CLK
X
X
X
↑
↑
L
D
X
X
X
H
L
X
OUTPUT
Q
H
L
H
1
PINOUTS
14-Pin DIP
Top View
CLR1
D1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
CLR2
D2
CLK2
PRE2
Q2
Q2
14-Lead Flatpack
Top View
CLR1
D1
CLK1
PRE1
Q1
Q1
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
CLR2
D2
CLK2
PRE2
Q2
Q2
LOGIC SYMBOL
PRE1
CLK1
D1
CLR1
PRE2
CLK2
D2
CLR2
(4)
(3)
(2)
(1)
(10)
(11)
(12)
(13)
(9)
(8)
Q2
Q2
S
C1
D1
R
(5)
(6)
Q1
Q1
Q
L
H
H
L
H
Q
o
1
H
L
Q
o
Note:
1. The output levels in this configuration are not guaranteed to meet the minimum
levels for V
OH
if the lows at preset and clear are near V
IL
maximum. In
addition, this configuration is nonstable; that is, it will not persist when either
preset or clear returns to its inactive (high) level.
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and IEC
Publication 617-12.
1
LOGIC DIAGRAM
PRE
CLR
Q
CLK
Q
D
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
1.9
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
0.40
0.25
V
V
OH
V
I
OS
I
OL
mA
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
a frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
[i=s]This post was last edited by qwqwqw2088 on 2020-3-6 10:19[/i]Battery testing equipment is essential equipment and infrastructure for the battery manufacturing industry. As the demand for lithium ...
Abstract: This paper introduces the internal structure and pin functions of the LXT971A network communication interface circuit, and gives the hardware interface implementation method of network commu...
This is to run the svn version of FTK on RT-Thread, using the mini2440 branch. In order to let everyone see the effect intuitively, it is made into a QEMU virtual machine. After downloading, unzip it ...
How can we get the highest performance from an A/D converter? The obvious answer is to use good design and board layout, but there are other techniques that can be used to improve performance. We can ...[Details]
In response to a series of problems caused by the backwardness of traditional water meters, the Ministry of Construction of China has proposed the requirement of "three meters per household" for ur...[Details]
Lithium-ion battery is a widely used rechargeable battery. It has the advantages of high single-cell operating voltage, small size, light weight, high energy density, long cycle life, rapid full ch...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
0Introduction
In oil drilling, accurate measurement of wellbore posture is the premise of wellbore trajectory control. To this end, this paper fully combines the advantages of single-chip ...[Details]
E6601A is Agilent's new generation of comprehensive tester platform, designed to provide low-cost calibration solutions for mobile phone manufacturers. It uses an open Windows® XP platform, allowi...[Details]
introduction
Mobile phones, MP3 players, hard disk players, digital cameras, PDAs and other devices are all controlled by navigation keys. Currently, the more popular navigation key contro...[Details]
introduction
Controller Area Network (CAN) is a bus standard proposed by Bosch of Germany to solve the information communication between automotive electronic control units. With its excel...[Details]
Abstract: By controlling the supply voltage of the radio frequency (RF) power amplifier (PA) in a CDMA/WCDMA cellular phone, the PA efficiency can be improved, heat generation can be reduced, and t...[Details]
Fieldbus is an open, digital, multi-point communication control system local area network, and is one of the most promising technologies in today's automation field. CAN bus is a hot application in fi...[Details]
0 Introduction
Mobile robot is a comprehensive system that integrates multiple functions such as environmental perception, dynamic decision-making, behavior control and execution. Its motion...[Details]
Low-frequency induction communication is to generate a certain alternating current in the transmitter after the data to be transmitted is modulated by a low-frequency carrier, amplified by the...[Details]
In the new generation of automotive exterior mirrors, the number of built-in functions has increased significantly: side retro-reflectors or turn signals/flashlights, door exterior lights, defroste...[Details]
1 Introduction
The research is about a basic human parameter tester that can measure parameters such as body temperature, pulse and breathing interval. These parameters and records are the...[Details]
introduction:
With the development of power electronics, the application scope of inverter control technology and industrial field bus is becoming wider and wider. This system successfully...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
