Incorporates two enable inputs to simplify cascading and/or
data reception
1.2μ
CMOS
- Latchup immune
High speed
Low power consumption
Single 5 volt supply
Available QML Q or V processes
Flexible package
- 16-pin DIP
- 16-lead flatpack
UT54ACS139 - SMD 5962-96546
UT54ACTS139 - SMD 5962-96547
DESCRIPTION
The UT54ACS139 and the UT54ACTS139 are designed to be
used in high-performance memory-decoding or data-routing ap-
plications requiring very short propagation delay times.
The devices consist of two individual two-line to four-line de-
coders in a single package. The active-low enable input can be
used as a data line in demultiplexing applications.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
ENABLE
INPUTS
G
H
L
L
L
L
SELECT
INPUTS
B
X
L
L
H
H
A
X
L
H
L
H
Y0
H
L
H
H
H
OUTPUT
Y1
H
H
L
H
H
Y2
H
H
H
L
H
Y3
H
H
H
H
L
PINOUTS
16-Pin DIP
Top View
IG
1A
1B
1Y0
1Y1
1Y2
1Y3
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
16-Lead Flatpack
Top View
1G
1A
1B
1Y0
1Y1
1Y2
1Y3
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
LOGIC DIAGRAM
(4)
1G
(1)
(5)
(6)
SELECT
1A
1B
(2)
(3)
(7)
(12)
2G
(15)
(11)
(10)
SELECT
2A
2B
(14)
(13)
(9)
1Y0
1Y1
1Y2
DATA
1Y3
2Y0
2Y1
2Y2
2Y3
1
LOGIC SYMBOL
1A
1B
1G
(2)
(3)
(1)
X/Y
1
2
EN
0
1
2
3
(4)
(5)
(6)
(7)
(12)
(11)
(10)
(9)
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
1A
1B
1G
(2)
(3)
(1)
DMUX
0
1
0
G
---
3
0
1
2
3
(4)
(5)
(6)
(7)
(12)
(11)
(10)
(9)
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
2A
2B
2G
(14)
(13)
(15)
2A
2B
2G
(14)
(13)
(15)
Note:
1. Logic symbols in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
I
OS
P
total
I
DDQ
ΔI
DDQ
Short-circuit output current
2 ,4
ACTS/ACS
Power dissipation
2, 8, ,9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
V
O
= V
DD
and V
SS
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
-200
200
1.8
10
1.6
mA
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
8
.5V
DD
.7V
DD
-1
1
0.40
0.25
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
V
V
OH
V
I
OL
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
[size=4][color=#000][font=Arial, Verdana, sans-serif] PFC is a circuit that solves the grid pollution problem caused by traditional AC rectifier circuits. The rectifier bridge of the conventional rect...
It's urgent. I finally downloaded the mass production tool of Tsinghua Unigroup USB flash drive, but it shows that the chip information is not found. I used ChipGenius_3.0 (USB device chip model detec...
I use the microcontroller's P1 port to connect to the data output port of ADC0809. When programming in C language, the microcontroller's P2.7 ends at the OE of 0809. Can the other pins of P2 port stil...
The system clock is the heart and power source of the chip, so we start with the clock. The subsequent ADC and TIM are all based on the clock.
In STM32F746, there are 5 most important clock sources: H...
In telecom and other applications where high-voltage negative rails are used, an instrumentation amplifier can be simply combined with discrete components to implement high current sensing to protect ...
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
Current Development Status of DVR Market
A DVR, or digital video recorder, uses a hard disk for recording, unlike traditional analog video recorders. It's often called a DVR because it's a com...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
A scale, a large, ground-mounted scale, is typically used to measure the tonnage of truck cargo. It's the primary weighing device used in factories, mines, and businesses for bulk cargo measurement...[Details]
Puttshack's Trackaball uses the Nordic nRF54L15 system-on-chip (SoC) to monitor sensors and enable Bluetooth low energy connectivity, while the nPM2100 power management integrated circuit (PMIC) ...[Details]
introduction
The OMAP-L138 dual-core processor is a new generation of low-power single-chip systems (SoCs) from TI. It is widely used in communications, industrial, medical diagnostic, and aud...[Details]
On August 20, it was reported that the specifications of Intel's upcoming Panther Lake mobile processor appeared on the Intel GFX CI website, which mainly focuses on Intel's open source Linux drive...[Details]
0 Introduction
With a rapidly aging population, a young couple is now required to care for an increasing number of elderly people, leading to a growing difficulty in providing care for them. E...[Details]
In microwave amplification circuits, the power chip is the core of the entire circuit. A large number of semiconductor devices in the chip will generate a lot of heat when working. If the heat diss...[Details]
We know that the power output by the engine does not directly act on the wheels to drive the car, but needs to pass through a series of power transmission mechanisms. So how is the power transmitte...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
