Incorporates two enable inputs to simplify cascading and/or
data reception
1.2μ
CMOS
- Latchup immune
High speed
Low power consumption
Single 5 volt supply
Available QML Q or V processes
Flexible package
- 16-pin DIP
- 16-lead flatpack
UT54ACS139 - SMD 5962-96546
UT54ACTS139 - SMD 5962-96547
DESCRIPTION
The UT54ACS139 and the UT54ACTS139 are designed to be
used in high-performance memory-decoding or data-routing ap-
plications requiring very short propagation delay times.
The devices consist of two individual two-line to four-line de-
coders in a single package. The active-low enable input can be
used as a data line in demultiplexing applications.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
ENABLE
INPUTS
G
H
L
L
L
L
SELECT
INPUTS
B
X
L
L
H
H
A
X
L
H
L
H
Y0
H
L
H
H
H
OUTPUT
Y1
H
H
L
H
H
Y2
H
H
H
L
H
Y3
H
H
H
H
L
PINOUTS
16-Pin DIP
Top View
IG
1A
1B
1Y0
1Y1
1Y2
1Y3
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
16-Lead Flatpack
Top View
1G
1A
1B
1Y0
1Y1
1Y2
1Y3
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
LOGIC DIAGRAM
(4)
1G
(1)
(5)
(6)
SELECT
1A
1B
(2)
(3)
(7)
(12)
2G
(15)
(11)
(10)
SELECT
2A
2B
(14)
(13)
(9)
1Y0
1Y1
1Y2
DATA
1Y3
2Y0
2Y1
2Y2
2Y3
1
LOGIC SYMBOL
1A
1B
1G
(2)
(3)
(1)
X/Y
1
2
EN
0
1
2
3
(4)
(5)
(6)
(7)
(12)
(11)
(10)
(9)
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
1A
1B
1G
(2)
(3)
(1)
DMUX
0
1
0
G
---
3
0
1
2
3
(4)
(5)
(6)
(7)
(12)
(11)
(10)
(9)
1Y0
1Y1
1Y2
1Y3
2Y0
2Y1
2Y2
2Y3
2A
2B
2G
(14)
(13)
(15)
2A
2B
2G
(14)
(13)
(15)
Note:
1. Logic symbols in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
I
OS
P
total
I
DDQ
ΔI
DDQ
Short-circuit output current
2 ,4
ACTS/ACS
Power dissipation
2, 8, ,9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
V
O
= V
DD
and V
SS
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
-200
200
1.8
10
1.6
mA
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
8
.5V
DD
.7V
DD
-1
1
0.40
0.25
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
V
V
OH
V
I
OL
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
[i=s]This post was last edited by dontium on 2015-1-23 13:35[/i] I am now going to use 2812 to make a product, which means burning the flash. In addition to writing the corresponding cmd file, do I ne...
I started working in the communications industry in 1999, then in the power electronics industry in 2004, and will soon be working in the measurement and control industry. Each time I changed industri...
Does anyone know where I can download the book "Windows CE Advanced Programming and Detailed Examples" for free? I'm in urgent need of books on embedded systems. Can any expert give me some advice? Th...
[color=#666666][backcolor=rgb(255, 247, 219)][font=宋体]FRAM is an environmentally friendly memory, the written data cannot be stolen through physical analysis, and there is no backup battery requiremen...
1. Several nouns
ABI:
The specifications that an executable file must follow in order to run in a specific execution environment;
Separately generated relocatabl...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
Whether it is an electric car or an ordinary fuel car, for the vast majority of car buyers, the final cost of use is what they care about most. For fuel cars, how to save fuel is what drivers care ...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
The most significant feature of IPS panels is that both electrodes are located on the same surface, unlike other LCD panels, which have electrodes arranged on top and bottom surfaces in a three-dim...[Details]
The structure of an LCD TV primarily consists of the LCD display module, power module, driver module (primarily including the main driver board and tuner board), and keypad module. LCD display modu...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
Smartphones have become essential digital devices, and the growing number of smartphone-centric applications is enriching people's lives. As users, they desire a better app experience and a wider r...[Details]
Electric vehicles are becoming increasingly popular, with increasingly longer ranges. There are two ways to charge electric vehicles: slow charging and fast charging. Which is the most suitable? Sl...[Details]
Reflow soldering is one of the most commonly used methods in electronics manufacturing, allowing for the soldering of large numbers of components in a relatively short time. However, any experience...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
1. Fault phenomenon and cause analysis
1. During the operation of the equipment, the expansion sleeve is subjected to a large torque, and the mating surfaces of the shaft and the sleeve move...[Details]
To improve the lateral active safety of intelligent connected vehicles, the identification and definition of unexpected functional safety scenarios for the EPS (Electronic Steering System) ...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
In the field of communications power supplies, AC/DC rectifier power supplies are called primary power supplies or basic power supplies, while DC/DC converters are called secondary power supplies. ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
