EEWORLDEEWORLDEEWORLD

Part Number

Search

530CA28M0000DG

Description
CMOS Output Clock Oscillator, 28MHz Nom, ROHS COMPLIANT, SMD, 6 PIN
CategoryPassive components    oscillator   
File Size215KB,12 Pages
ManufacturerSilicon Laboratories Inc
Environmental Compliance  
Download Datasheet Parametric View All

530CA28M0000DG Overview

CMOS Output Clock Oscillator, 28MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

530CA28M0000DG Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerSilicon Laboratories Inc
Reach Compliance Codeunknown
Other featuresTRAY
Frequency Adjustment - MechanicalNO
frequency stability50%
JESD-609 codee4
Manufacturer's serial number530
Installation featuresSURFACE MOUNT
Nominal operating frequency28 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeCMOS
physical size7.0mm x 5.0mm x 1.85mm
Maximum supply voltage3.63 V
Minimum supply voltage2.97 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
Terminal surfaceNickel/Gold (Ni/Au)
Base Number Matches1
S i 5 3 0 / 5 31
R
EVISION
D
C
R Y S TA L
O
S C I L L A T O R
(XO)
(10 M H
Z T O
1.4 G H
Z
)
Features
Available with any-rate output
frequencies from 10 MHz to 945 MHz
and select frequencies to 1.4 GHz
3rd generation DSPLL
®
with superior
jitter performance
3x better frequency stability than
SAW-based oscillators
Internal fixed crystal frequency
ensures high reliability and low
aging
Available CMOS, LVPECL,
LVDS, and CML outputs
3.3, 2.5, and 1.8 V supply options
Industry-standard 5 x 7 mm
package and pinout
Pb-free/RoHS-compliant
Si5602
Ordering Information:
See page 7.
Applications
SONET/SDH
Networking
SD/HD video
Test and measurement
Clock and data recovery
FPGA/ASIC clock generation
Pin Assignments:
See page 6.
(Top View)
NC
OE
GND
1
2
3
6
5
4
V
DD
Description
The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry
to provide a low jitter clock at high frequencies. The Si530/531 is available
with any-rate output frequency from 10 to 945 MHz and select frequencies to
1400 MHz. Unlike a traditional XO, where a different crystal is required for
each output frequency, the Si530/531 uses one fixed crystal to provide a
wide range of output frequencies. This IC based approach allows the crystal
resonator to provide exceptional frequency stability and reliability. In addition,
DSPLL clock synthesis provides superior supply noise rejection, simplifying
the task of generating low jitter clocks in noisy environments typically found in
communication systems. The Si530/531 IC based XO is factory configurable
for a wide variety of user specifications including frequency, supply voltage,
output format, and temperature stability. Specific configurations are factory
programmed at time of shipment, thereby eliminating long lead times
associated with custom oscillators.
®
CLK–
CLK+
Si530 (LVDS/LVPECL/CML)
OE
NC
GND
1
2
3
6
5
4
V
DD
Functional Block Diagram
V
DD
CLK– CLK+
NC
CLK
Si530 (CMOS)
Fixed
Frequency
XO
Any-rate
10–1400 MHz
DSPLL
®
Clock
Synthesis
OE
NC
GND
1
2
3
6
5
4
V
DD
CLK–
CLK+
Si531 (LVDS/LVPECL/CML)
OE
GND
Rev. 1.1 6/07
Copyright © 2007 by Silicon Laboratories
Si530/531
When it comes to power module selection, you must have been troubled by these four questions!
[size=4]在日趋激烈的市场竞争中,产品的快速设计与开发无疑已经成为领先致胜、快速占领商机的必要条件。在项目经理的“鞭策”和项目周期越来越短的普遍情况下,模块化开发,平台化开发,方案引用式开发模式已经被越来越多的系统设计人员和硬件工程师接受使用。[/size] [size=4][/size] [size=4] [/size] [size=4]任何一个电子产品的开发,都逃不开电源的设计。如果将产...
ohahaha Power technology
Have the TDI and NDIS drivers changed in Win7?
Can the firewall software based on TDI and NDIS developed under WinXP run normally in Win7? Does Win7 continue to support TDI drivers? Are there any changes and adjustments to NDIS?...
sun77xujing Embedded System
LPC1500 Experience + 5_LCD1602 drive circuit design
[i=s]This post was last edited by youzizhile on 2014-7-27 21:17[/i] Board connection: Use the J1.J2.J6.J74 interfaces reserved on the board, and use Dupont wires and pins to connect the LCD1602 and LP...
youzizhile NXP MCU
ST8 for motor control development
Heroes, I have encountered a very difficult problem when using ST8 to develop motor control. I would like to ask for your advice. WhatI want to control is a brushless DC motor. Of course, PWM control ...
laofuzi stm32/stm8
TI MSP430 Environmental Testing Tool
First of all, I would like to thank TI and the forum for organizing this event. After receiving the LAUNCHPAD board, I have not been able to get around to it due to some trivial matters at work. But t...
ccgzkr Microcontroller MCU
Why can't the motor speed be changed when the example that comes with the DRV8301-HC-EVM RevD D development board uses the open-loop PWM speed regulation mode?
The examples that come with the DRV8301-HC-EVM RevD DEMO development board include the control routines for BLDC motors. Why can't the motor speed be changed when the open-loop PWM speed regulation mo...
liuqiuming Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 192  2804  2697  554  2731  4  57  55  12  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号