530VC92M0000DGR datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 530VC92M0000DGR

530VC92M0000DGR: DescriptionCMOS Output Clock Oscillator, 92MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

530VC92M0000DGR Overview

CMOS Output Clock Oscillator, 92MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

530VC92M0000DGR Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
package instruction	ROHS COMPLIANT, SMD, 6 PIN
Reach Compliance Code	unknown
Other features	TAPE AND REEL
Frequency Adjustment - Mechanical	NO
frequency stability	7%
JESD-609 code	e4
Manufacturer's serial number	530
Installation features	SURFACE MOUNT
Nominal operating frequency	92 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS
physical size	7.0mm x 5.0mm x 1.85mm
Maximum supply voltage	1.89 V
Minimum supply voltage	1.71 V
Nominal supply voltage	1.8 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)
Base Number Matches	1

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

Stabilized multi-voltage rectifier circuit with adjustable output voltage

Switching battery charger circuit diagram

AC voltage detection circuit

1Hz～100kHz square wave-triangular wave oscillator

S9803 drive relay circuit

wince infrared and serial port: I need to add infrared support recently. I use 2440 and connect an infrared receiver to the board. I want to add infrared. Are the drivers used for infrared and serial ports the same? Or do I need to ...; zzqqking Embedded System

Please advise on the procedure of 2812 external EEPROM: In the given example/********************************************************************Function name: unsigned int EEPROM_Read_Status(void)Purpose: EEPROM read statusInput: NoneOutput: None*********...; mhlllf Microcontroller MCU

Why do the impedances of the two input terminals of the op amp need to be matched?: Taking a simple reverse proportional circuit built with an op amp as an example, what is the use of the resistor added to the non-inverting end?...; PCB板 Analog electronics

I have a conceptual question, signal pin?: I just started to get involved in hardware. I was reading a book about PowerLogic and found that it mentioned a kind of pin as Signal Pin. It said that this pin should be used for power/ground. Howeve...; zhanghuiyang Embedded System

I would like to ask ST sales support whether the STM32F10X motor library can support brushless DC motors.: As the title says: Can the STM32F10X motor library support brushless DC motors?The STM32F10X motor library supports PMSM under FOC. Since there are differences in the understanding of the distinction ...; jhxajh stm32/stm8

SWD Interface: How many wires do I need to connect to debug with SWD? Do I need to connect other wires besides SWDIO SWCLK?...; farmerhou stm32/stm8

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components