EEWORLDEEWORLDEEWORLD

Part Number

Search

5SB5.2S

Description
DC-DC Unregulated Power Supply Module, 1 Output, 1.5W, Hybrid,
CategoryPower/power management    The power supply circuit   
File Size242KB,7 Pages
ManufacturerPico Electronics Inc.
Download Datasheet Parametric View All

5SB5.2S Overview

DC-DC Unregulated Power Supply Module, 1 Output, 1.5W, Hybrid,

5SB5.2S Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerPico Electronics Inc.
Reach Compliance Codecompliant
ECCN codeEAR99
Analog Integrated Circuits - Other TypesDC-DC UNREGULATED POWER SUPPLY MODULE
Maximum input voltage6.5 V
Minimum input voltage4 V
Nominal input voltage5 V
JESD-30 codeR-XDMA-P4
JESD-609 codee0
Number of functions1
Output times1
Number of terminals4
Maximum operating temperature70 °C
Minimum operating temperature-25 °C
Maximum output voltage5.45 V
Minimum output voltage4.95 V
Nominal output voltage5.2 V
Package body materialUNSPECIFIED
Package shapeRECTANGULAR
Package formMICROELECTRONIC ASSEMBLY
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Certification statusNot Qualified
surface mountNO
technologyHYBRID
Temperature levelOTHER
Terminal surfaceTIN LEAD
Terminal formPIN/PEG
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
Maximum total power output1.5 W
Fine-tuning/adjustable outputNO
Base Number Matches1
SERIES B/SB
SURFACE MOUNT and PLUG­IN
Hi Reliability
Ultra­Miniature 
Isolated DC­DC Converters
Up to 2.5 Watts
This series of unregulated DC­DC converters comes in a miniaturized encapsulated package. 188
different models are available. The units feature single and isolated dual outputs. They will operate over
the temperature range of ­25º C to +70º C. No heat sink is required.
TYPICAL CHARACTERISTICS:
Test conditions: 25º C ambient and input voltage
at nominal value unless otherwise specified. 
LINE REGULATION: OUTPUT IS DIRECTLY
PROPORTIONAL TO THE INPUT. 
Input voltage range:
Low Profile 0.3" Height! Up to 2.5 Watts
No Heat Sink or Electrical Derating Required
OPTIONS AVAILABLE
Per Mil. Std. 883 
Expanded operating temp. (­55º C to +85º C) 
Stabilization Bake (125º C ambient) 
Temperature Cycle (­55º C to +125º C) 
Hi Temp, full power burn in (100% power, 125º C
case temp) 
FEATURES
5V models: 4 to 6.5V DC
12V models: 9 to 15V DC
15V models: 12 to 18V DC
24V models: 17 to 28V DC
28V models: 21 to 32V DC
48V models: 25 to 50V DC
Output voltage tolerance at full load:
 
Up to 2.5 watt output at 70º C ambient 
Encapsulated semiconductors, conservatively rated
for maximum reliability 
Ultra­miniature size (0.3" Height) 
6 input voltage ranges 5, 12, 15, 24, 28 and 48V DC 
100 megohm @ 500V DC isolation 
Single and dual isolated output 
No heat sink required
 
5V models ± 0.25V 
9V models ± 0.3V 
12V & 15V models ± 0.4V 
24V & 28V models ± 0.5V 
48V models ± 0.7V
Converter frequency: 20 ­ 40 KHz 
Output temperature coefficient: 0.02%/ºC 
Operating temperature: ­25º C to +70º C ambient.
No heat sink is required. 
Storage temperature: ­55º C to +125º C 
Isolation: 100 megohms min. @ 500V DC 
Short circuit protection: Temporary 
SERIES B/SB ­ SINGLE OUTPUT 
Quartus II 8.0 installation problem
After I installed Quartus 8.0 (successfully cracked), I used its built-in IP generation tool to generate a three-speed Ethernet IP core and a simulation file. When I opened the simulation tool Questas...
eeleader-mcu FPGA/CPLD
About MOS tube recommendation
The 12VDC signal controls the on and off of the 24VDC relay. I want to use a MOS tube to drive it. Is there any economical and small MOS tube to recommend? If there is any other better solution, pleas...
xhd1099924128 Analog electronics
Can someone help me? About the 320F28035 clock problem
I am working on a DSP28035 chip, and the waveform is not correct when configuring the clock in the experiment. So I want to use DSP to control the TOPWAY LCD screen but it fails!DSP+12M crystal oscill...
huwei_harry Microcontroller MCU
Key points of welding, introduction of manual welding method
[i=s]This post was last edited by bjhyyq on 2017-7-19 11:35[/i] [align=left][size=14px][b]Preheating 1:[/b]Put the soldering tip in full contact with the solder joint. Figure 1 shows how to heat the s...
bjhyyq PCB Design
Newbie~Help me with MSP430 program burning problem
I use IAR version 5.1, and the MCU model is MSP430F19. I can debug the software normally, but the following error will occur when the hardware is connected. The same error occurs when the MCU and emul...
我爱小恶习 Microchip MCU
CCS3.3编译错误 error:this declaration has no storage class or type specifier
The following error occurs when compiling the program with CCS3.3: error: this declaration has no storage class or type specifier error: declaration is incompatible with "volatile struct PIE_CTRL_REGS...
ndt126 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2462  2868  1132  2388  2371  50  58  23  49  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号