I have read some discussions about ADAS radars by friends on the forum. I wonder if you know that there is a frequency planning of the Ministry of Industry and Information Technology. In fact, it can ...
I'm working on an audio project recently, and I'm going to DIY a USB sound card, using the SSS1629 solution, with the following parameters: USB protocol: USB specification v2.0 full speed; USB audio p...
Theoretical references for Fourier transform or FFT: [1] [url]http://www.dspguide.com/ch12/2.htm[/url] The Scientist and Engineer's Guide to Digital Signal Processing, By Steven W. Smith, Ph.D. [2] Ca...
I recently started to develop on TI's DM355. Question 1: I have always been confused about the ROM boot loader of DM355. Does anyone have some information about the ROM boot loader of DM355? Question ...
Write a matrix keyboard driver in wince. (7 rows * 6 columns) Matrix keyboard, lead out 13 wires, the GPIO connected to the 6 columns is set as the external interrupt port, and the GPIO direction conn...
Look at the picture and talk about it. This is a circuit similar to a flashlight, which charges the capacitor (C7-C10) and discharges it instantly. The voltage across the capacitor must be charged to ...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
store
To prevent moisture, LEDs should be stored in a dry and ventilated environment with a storage temperature of -40°C to +100°C and a relative humidity below 85%.
The LED should be use...[Details]