EEWORLDEEWORLDEEWORLD

Part Number

Search

585L28610CBT

Description
Clipped Sine Output Oscillator
CategoryPassive components    oscillator   
File Size284KB,3 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

585L28610CBT Overview

Clipped Sine Output Oscillator

585L28610CBT Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
Other featuresTR, 7 INCH
Ageing1 PPM/FIRST YEAR
Maximum control voltage2.5 V
Minimum control voltage0.5 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate8 ppm
frequency stability1%
JESD-609 codee4
Installation featuresSURFACE MOUNT
Nominal operating frequency28.63636 MHz
Maximum operating temperature70 °C
Minimum operating temperature-20 °C
Oscillator typeCLIPPED SINE
Output impedance10000 Ω
Output level0.8 V
physical size7.0mm x 5.0mm x 2.1mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Base Number Matches1
Model 585
Temperature Compensated Crystal Oscillator
FEATURES
Clipped Sine Wave Output
Optional Voltage Control for Frequency Tuning [VCTCXO]
7.0mm x 5.0mm Surface Mount Package
Frequency Range 5 – 52 MHz
Fundamental Crystal Design
Frequency Stability, Options from, ±0.5ppm ~ ±2.5ppm
Operating Voltage, +2.8Vdc ~ +5.0Vdc
Operating Temperature to -40°C to +85°C
Tape & Reel Packaging Standard, EIA-418
RoHS/Green Compliant [6/6]
APPLICATIONS
The Model 585 is a quartz based analog TCXO with a Clipped Sine output and optional frequency tuning.
M585 is suitable for applications such as wireless communications, base stations, small cells, broadband access
and test equipment.
ORDERING INFORMATION
585
SUPPLY VOLTAGE
T = +2.8Vdc
R = +3.0Vdc
L = +3.3Vdc
S = +5.0Vdc
PACKAGING OPTIONS
T - 1k pcs./reel
FREQUENCY TUNING [AFC]
T = TCXO [no AFC]
A = ±5ppm minimum [VCTCXO]
B = ±8ppm minimum [VCTCXO]
[V
C
= +1.5Vdc ± 1.0Vdc]
OPERATING TEMPERATURE RANGE
H = -10°C to +60°C
C = -20°C to +70°C
D = -30°C to +85°C
I = -40°C to +85°C
1
FREQUENCY
Product Frequency Code
[3 digits]
Refer to document 016-1454-0,
Frequency Code Tables.
FREQUENCY STABILITY *
05
10
15
20
25
=
=
=
=
=
±
±
±
±
±
0.5
1.0
1.5
2.0
2.5
ppm
ppm
ppm
ppm
ppm
2
* Frequency vs. Temperature Only
1] Limited availability. Consult factory.
2] Only available with temperature range codes "H" and "C".
Not all performance combinations and frequencies may be available.
Contact your local CTS Representative or CTS Customer Service for availability.
Document No. 008-0522-0
Page 1 - 3
Rev. B
www.ctscorp.com
Video tutorial on learning MCU from scratch - Lecture 01: Building C51 integrated development environment
Zero-based MCU video tutorial - Lecture 01 Building C51 integrated development environment This lecture first builds a 51 MCU hardware and software development system, and demonstrates the process of ...
flykick Embedded System
Regulator tube usage help
As shown in the figure, for such a circuit, the voltage at the WAKE point is about 20V without a voltage regulator. Will the voltage at the WAKE point be 18V after adding a voltage regulator?...
Kkk- Analog electronics
STM8S+ firmware library program is too large
-------- Segments -------- start 00008080 end 0000876b length 1771 segment .const start 0000876e end 00009417 length 3241 segment .text start 00000000 end 00000000 length 0 segment .bsct start 0000000...
geyang1111 stm32/stm8
Purgatory Legend-Edge Detection Battle
Edge detection is to detect the jump of input signal or FPGA internal logic signal, that is, the detection of rising or falling edge of the signal. To learn edge detection circuit, we should first lea...
梦翼师兄 FPGA/CPLD
Chip bottom routing, interference situation, weak questions
A chip, in which two pins are two signals A and B that are easily interfered with. They are connected to the outside. Assume that the chip is on the front. In the first case, both extend to the right,...
ienglgge PCB Design
Can multiple device objects be created in a driver, and do these device objects share the same dispatch routine?
Question: Can I create multiple device objects in a driver, and do the IRPs sent to different device objects share the same dispatch routine? Background of the question: I want to write a filter drive...
chely Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1371  1344  97  1777  717  28  2  36  15  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号