EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63104-490Y

Description
Line Driver, 1 Driver, Hybrid, CDIP24
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size124KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63104-490Y Overview

Line Driver, 1 Driver, Hybrid, CDIP24

BUS-63104-490Y Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
package instructionDIP, DIP24,1.1
Reach Compliance Codecompliant
ECCN codeEAR99
Differential outputYES
Number of drives1
Interface integrated circuit typeLINE DRIVER
JESD-30 codeR-XDIP-T24
JESD-609 codee0
Number of terminals24
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Minimum output swing29 V
Package body materialCERAMIC
encapsulated codeDIP
Encapsulate equivalent codeDIP24,1.1
Package shapeRECTANGULAR
Package formIN-LINE
Peak Reflow Temperature (Celsius)NOT SPECIFIED
power supply5,+-12/+-15 V
Certification statusNot Qualified
Maximum receive delay
Filter level38535V;38534K;883S
surface mountNO
technologyHYBRID
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formTHROUGH-HOLE
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
Base Number Matches1
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
Why can the reference layer of PCB also be the power layer?
As shown in the figure above, in a 4-layer PCB stack, why can the differential line refer to the third layer (Power layer)? I understand that ordinary single-ended signals must be referenced to the gr...
xiaominwzj PCB Design
I drew the schematic using protues software, and after converting it into a PCB diagram, I found that only the buzzer was not packaged.
I finished drawing the schematic diagram using protues software. After converting it into PCB diagram, I found that only the buzzer was not packaged. After checking online, I found that I had to draw ...
圈在指尖 PCB Design
Questions about SPI in 5438
The direction of the signal on the middle line is from slave to master. Does it mean that the slave controls the UCxSTE bit of the master? But I think it should be manually decided in the program whet...
zzbaizhi Microcontroller MCU
Basic knowledge of automobile body design
This article provides some basic knowledge of automobile body design, which is suitable for learning and training of relevant departments in the automobile industry. Main contents: Main components of ...
frozenviolet Automotive Electronics
Please help me read the next program, which is to clear the RAM from 0200H to 05FFH! Is it correct?
Please help me look at the next program, which is to clear the RAM from 0200H to 05FFH!Is this correct? Because it feels like it should be written. Shouldn't Address be +2 each time?unsigned int *ptr;...
零晨 Microcontroller MCU
The ov7725 camera has serious distortion. What's going on?
I used the Wildfire ov7725 camera to display the image on the LCD screen, but the distortion was so severe that it was unusable.[img]https://s1.328888.xyz/2022/05/11/HIofe.jpg[/img] [img]https://s1.32...
xycgood FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 148  977  926  2361  1628  3  20  19  48  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号