EEWORLDEEWORLDEEWORLD

Part Number

Search

TMS-114-53-L-S-RA

Description
Board Connector, 14 Contact(s), 1 Row(s), Male, Right Angle, Solder Terminal, ROHS COMPLIANT
CategoryThe connector    The connector   
File Size226KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Environmental Compliance
Download Datasheet Parametric View All

TMS-114-53-L-S-RA Overview

Board Connector, 14 Contact(s), 1 Row(s), Male, Right Angle, Solder Terminal, ROHS COMPLIANT

TMS-114-53-L-S-RA Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
Connector typeBOARD CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialNOT SPECIFIED
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee3
MIL complianceNO
Manufacturer's serial numberTMS
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of rows loaded1
OptionsGENERAL PURPOSE
Terminal pitch1.27 mm
Termination typeSOLDER
Total number of contacts14
Base Number Matches1
Looking for STM32F107 USB HID 64-bit data transmission and reception routine
I am debugging the STM32F107 USB HID routine, and there is a problem that it can only receive but not send. I hope friends who have done this can provide a complete routine for learning. :)...
lzq2804 stm32/stm8
28335Change the output pin level through the GPADAT register?
The GPADAT register is used in the program to change the output pin level: #define GP_EN GpioDataRegs.GPADAT.bit.GPIO2 #define GP_OE GpioDataRegs.GPADAT.bit.GPIO4 #define GP_A GpioDataRegs.GPADAT.bit....
喜鹊王子 DSP and ARM Processors
Has anyone done WHQL certification?
My NDIS intermediate layer driver needs to be used on 64-bit Windows 7. Does it need to be WHQL certified? How can I obtain this certification?...
lhy705 Embedded System
Questions about using an oscilloscope differential probe to measure the voltage across a resistor and calculate the current
Due to the limited instruments at hand, I plan to use a differential probe to measure the voltage across the resistor as shown in the figure below, so as to calculate the laser current. There are two ...
xiaxingxing Analog electronics
The WinCE device is identified as a USB disk.
Hello everyone. My development platform is S3C2410+WINCE5.0, and I want to make the WINCE device be recognized as a USB disk when it is connected to the PC via a USB cable. I changed the relevant regi...
liplip Embedded System
Allegro software usage
When placing a component in Allegro, it says W- (SPMHUT-48): Scaled value has been rounded off. Why can't the component be placed? I searched online and found that some people said the board frame is ...
一战到底 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1835  1309  1340  2206  159  37  27  45  4  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号