Ortel’s Model 755MM-S is a recently developed 1550 nm transmitter
suitable for link lengths of up to 20Km. The 75Ω RF video input
supports frequencies up to 870 MHz. Also integrated into the RF/Optical
design are Ortel’s low chirp control and noise suppression circuitry.
Integrated within the design is Ortel’s patented pre distortion technology
to provide outstanding performance with any of Ortel’s wide range of
cooled broadband lasers. These modules have dual redundant power
supplies with SNMP capability.
It features Ortel’s proprietary Enhanced Optical Spectrum Reshaping
Technology with extremely high SBS suppression performance, making
it ideal for either FTTP or HFC network applications. The performance
specifications indicated below are subject to change
.
Performance Highlights
Features
Enhanced Optical Spectrum
Reshaping Technology
Optimized RF integration of
predistorter, amplifiers and
laser
Dual redundant power
supplies
Supports SNMP protocol
Complete, efficient laser bias
and TEC control circuitry
OEM/ODM opportunities
available through Ortel
Digital monitoring and control
ITU Wavelengths
Parameter
Operating Temperature Range
Wavelength (Multiple Options)
Optical Power
Frequency Response
CNR
CSO
CTB
SBS Suppression Capability
RF Input Return Loss
Optical Return Loss
Min
0
1530
5
47
47
-
-
19
16
40
Typ
25
-
-
-
48
-
-
-
-
-
Max
50
1560
-
870
-
-60
-65
23
Unit
°C
nm
dBm
MHz
dB
dBc
dBc
dBm
dB
dB
Applications
Video signal distribution to
HFC CATV and FTTP nodes
Video overlay in passive
optical networks (PON)
Replacement for Externally
Modulated Transmitters
-
-
Noise and distortion performance above assume 79 channel NTSC loading with no QAM, -5 dBm
received optical power. See following pages for complete specifications and operating/test
conditions.
For more information on this and other products:
Contact Sales at Ortel 626-293-3400, or visit www.emcore.com.
755MM-S 1550 nm Transmitter
PRELIMINARY DATASHEET- FEBRUARY, 2006
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in
excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect device reliability.
Parameter
Operating Temperature Range
Storage Case Temperature Range
RF Input Level
Symbol
T
OP
T
stg
-
Min.
0
-20
-
Max.
50
65
2
Unit
°
C
°
C
dBm
RF Characteristics
Parameter
Bandwidth
Frequency Response
RF Input Level with AGC
CNR
CSO
2
CTB
2
Input Impedance
Video Input Return Loss
Test Port Input Return Loss
1.Excludes tilt component.
2.CW carriers, 79 channel NTSC channel plan, 4 MHz noise bandwidth, -5 dBm received power, SMF-28 or equivalent.
Condition
-
-
-
-
-
-
45 – 870 MHz RF Input
45 to 870 MHz
45 to 870 MHz
Min
47
-
-10
47
-
-
-
16
16
Typ
-
-
-8
48
-
-
75
-
-
Max
870
1.5
-6
-
-60
-65
-
-
-
1
Unit
MHz
dB
p-p
dBm
dB
dBc
dBc
Ohms
dB
dB
Optical Characteristics
Parameter
Optical Output Power
SBS Threshold
Side Mode Suppression Ratio
Optical Return Loss
1
Condition
-
20 km SMF-28
-
APC style connector
Min
-
23
30
40
Typ
5
-
40
-
Max
-
-
-
-
Unit
dBm
dBm
dB
dB
1. In order to prevent reflection-induced distortion, the laser must be connected to an optical cable having a return loss of at least 55 dB for discrete
reflections and 30 dB for distributed reflections
2 of 5
755MM-S 1550 nm Transmitter
PRELIMINARY DATASHEET- FEBRUARY, 2006
Power Requirements
Parameter
AC Input Range
DC Input Range
Power
Min.
94
50
36
-
Max.
245
60
60
50
Unit
Vac
Hz
Vdc
W
Package Characteristics
Parameter
Height
Width
Depth
Weight
Dimension
1.75 (44), 1U
19 (483)
17.77(452) with fans
9.0 (4)
Unit
in. (mm.)
in. (mm.)
in. (mm.)
lbs. (kg.)
Part Number / Ordering Information
(Note: customization can be made available upon request)
755MM-S
-
-
-
- XX -
Channel Plan
A = NTSC 80-Ch
Output
05 = 5 dBm (Std)
SBS
A = 23 dBm (Std)
Connectors
SC = SC/APC
FC = FC/APC
EC = E2000/APC
ITU Wavelengths
ee= 21, 1560.61nm
:
ee= 59, 1530.33 nm
AC Power Cord
NA = N.AMERICA
UK = U.K. & IRE.
EU = EUROPE
EC = EC NEMA
JP = JAPAN
3 of 5
755MM-S 1550 nm Transmitter
PRELIMINARY DATASHEET- FEBRUARY, 2006
ITU Wavelength Channel Designations
Channel
21
23
25
27
29
31
33
Wavelength
(nm)
1560.61
1558.98
1557.36
1555.75
1554.13
1552.52
1550.92
Channel
35
37
39
41
43
45
47
Wavelength
(nm)
1549.32
1547.72
1546.12
1544.53
1542.94
1541.35
1539.77
Channel
49
51
53
55
57
59
Wavelength
(nm)
1538.19
1536.61
1535.04
1533.47
1531.90
1530.33
4 of 5
755MM-S 1550 nm Transmitter
PRELIMINARY DATASHEET- FEBRUARY, 2006
Laser Safety Information
This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH
Class IIIb laser product. This device has been classified with the FDA/CDRH under accession number 0220800.
Single-mode bulkhead receptacles with internal SC/APC connectors (standard).
Wavelength = 1.5
μm.
Maximum power = 30 mW.
Product is shipped with internal AC/DC and DC/DC power supply converters.
Caution: Use of controls, adjustments and procedures other than those specified herein may result in
hazardous laser radiation exposure.
Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of
the product at any time without notice. EMCORE and the EMCORE logo are trademarks of EMCORE Corporation.
Use DSP to generate PWM waveform (two complementary waveforms), use a boost circuit to drive KD301. As a result, the voltage of the waveform is completely pulled down as soon as it is connected. KD301...
The GSM digital mobile communication system was designed by a standardization committee composed of major European telecom operators and manufacturers. It was developed on the basis of the cellular sy...
[color=#000000]Share a useful little experience I saw from Zhiyuan Electronics[/color] [p=25, null, left][color=rgb(62, 62, 62)] Electronic engineers all know that the rapid development of semiconduct...
Abstract: This paper introduces the functions and features of the high-precision clock chip RTC-4553, which is newly launched by EPSON. It includes the internal structure and pins, function control an...
The jammer is a signal blocker, mainly composed of a chip and a radio transmitter. When the car owner presses the remote control lock button, the jammer interferes with the electronic lock receivin...[Details]
The most significant feature of IPS panels is that both electrodes are located on the same surface, unlike other LCD panels, which have electrodes arranged on top and bottom surfaces in a three-dim...[Details]
On August 25th, SK Hynix announced that it has completed development and entered mass production of its 321-layer, 2Tb QLC NAND flash memory product. This achievement marks the world's first applic...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
According to foreign media reports, secondary battery materials company POSCO Future M announced that it has successfully developed two experimental (prototype) positive electrode materials for the...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
In the summer of 2025, BlueOval SK, a joint venture between Ford and SK On, officially started production at its first battery factory in Kentucky.
According to the original plan, this w...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
This paper proposes a temperature real-time transmission and display solution based on LED optical data transmission, with Jingwei Yager low-power FPGA HR (Yellow River) series as the main controll...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
With the continuous development of the industrial automation industry, we are seeing an increasing number of intelligent devices using flexible, efficient, and precise robotic arms to p...[Details]
Reflow soldering is one of the most commonly used methods in electronics manufacturing, allowing for the soldering of large numbers of components in a relatively short time. However, any experience...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
A multilevel inverter converts a DC signal into a multilevel staircase waveform. Instead of a straight positive-negative output waveform, the output waveform of a multilevel inverter alternates in ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
