Enhanced N channel FET with no inherent diode to Vcc
Ω
25Ω bidirectional switches connect inputs to outputs
Pin compatible with 74F244, 74FCT244, and 74FCT244T
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
Available in QSOP, SOIC, and TSSOP packages
APPLICATIONS:
•
•
•
•
•
•
•
The QS3244 provides a set of eight high-speed CMOS TTL-compatible
bus switches in a pinout compatible with 74FCT244, 74F244, 74ALS/AS/
LS244 8-bit drivers. The low ON resistance (5Ω) of the 3244 allows inputs
to be connected to outputs without adding propagation delay and without
generating additional ground bounce noise. The two enable (xG) signals
turn the switches on similar to the
xG
signals of the 74’244.
QuickSwitch devices provide an order of magnitude faster speed than
conventional logic devices.
The QS3244 is characterized for operation at -40°C to +85°C.
DESCRIPTION:
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Power conservation
Capacitance reduction and isolation
Logic replacement (data processing)
Clock gating
Bus switching and isolation
FUNCTIONAL BLOCK DIAGRAM
1G
1A
1
1A
2
1A
3
1A
4
1Y
1
1Y
2
1Y
3
1Y
4
2G
2A
1
2A
2
2A
3
2A
4
2Y
1
2Y
2
2Y
3
2Y
4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
1
c
1999 Integrated Device Technology, Inc.
DECEMBER 1999
DSC-5722/3
IDTQS3244
HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
TERM
(2)
V
TERM
(3)
Description
Supply Voltage to Ground
DC Switch Voltage Vs
DC Input Voltage V
IN
AC Input Voltage (pulse width
≤20ns)
DC Output Current
Maximum Power Dissipation (T
A
= 85°C)
Storage Temperature
Max
–0.5 to +7
–0.5 to +7
–0.5 to +7
–3
120
0.5
–65 to +150
Unit
V
V
V
V
mA
W
°C
1G
1A
1
2Y
4
1A
2
2Y
3
1A
3
2Y
2
1A
4
2Y
1
G ND
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
V
CC
2G
1Y
1
2A
4
1Y
2
2A
3
1Y
3
2A
2
1Y
4
2A
1
V
TERM
(3)
V
AC
I
OUT
P
MAX
T
STG
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
CAPACITANCE
(T
A
= +25°C, f = 1MHz, V
IN
= 0V, V
OUT
= 0V)
Pins
Control Inputs
Quickswitch Channels (Switch OFF)
Typ.
3
5
Max.
(1)
5
7
Unit
pF
pF
QSOP/ SOIC/ TSSOP
TOP VIEW
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
1G, 2G
Ax, Yx
Output Enable
Data I/Os
Description
FUNCTION TABLE
(1)
1G
H
L
H
L
2G
H
H
L
L
1A, 1Y I/Os
Disconnected
1Ax = 1Yx
Disconnected
1Ax = 1Yx
2A, 2Y I/Os
Disconnected
Disconnected
2Ax = 2Yx
2Ax = 2Yx
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
2
IDTQS3244
HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 5V ± 5%
Symbol
V
IH
V
IL
I
IN
I
OZ
R
ON
V
P
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Switch ON Resistance
Pass Voltage
(2)
Test Conditions
Guaranteed Logic HIGH for Control Inputs
Guaranteed Logic LOW for Control Inputs
0V
≤
V
IN
≤
V
CC
0V
≤
V
OUT
≤
V
CC,
Switches OFF
V
CC
= Min., V
IN
= 0V, I
ON
= 30mA
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
V
IN
= V
CC
= 5V, I
OUT
= -5µA
Min.
2
—
—
—
—
—
3.7
Typ.
(1)
Max.
—
—
—
—
5
10
4
—
0.8
±1
±1
7
12
4.2
V
Unit
V
V
µA
µA
Ω
NOTES:
1. Typical values are at V
CC
= 5V and T
A
= 25°C.
2. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 5V
16
R
ON
(ohms)
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
V
IN
(Volts)
3
IDTQS3244
HIGH-SPEED CMOS QUICKSWITCH 8-BIT BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
∆I
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current per Control Input HIGH
(2)
Dynamic Power Supply Current per MHz
(3)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3.4V, f = 0
V
CC
= Max., A and Y Pins Open, Control Inputs Toggling @ 50% Duty Cycle
Max.
3
2.5
0.25
Unit
µA
mA
mA/MHz
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TTL-driven input (V
IN
= 3.4V, control inputs only). A and Y pins do not contribute to
∆Icc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and Y inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C, V
CC
= 5V ± 5%
C
LOAD
= 50pF, R
LOAD
= 500Ω unless otherwise noted.
Symbol
t
PLH
t
PHL
t
PZL
t
PZH
t
PLZ
t
PHZ
Parameter
Data Propagation Delay
(2)
Ax to Yx
Switch Turn-On Delay
1G, 2G
to Yx
Switch Turn-Off Delay
(2)
1G, 2G
to Yx
Min
.
(1)
0.5
0.5
Typ.
Max.
0.25
(3)
5.6
5.2
Unit
ns
ns
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
Live broadcast time: October 20 (Thursday) 10:00-11:30 am
Live Topic: TE Connectivity's Smart Building Solutions - Sensing and Connectivity, the Key to Smart Building DesignWatch LiveLive Broadcast In...
The project requires that the PDA device has a sound prompt when a text message comes. The hardware buzzer is connected to the headphone interface on the AC97 chip WM9712. The ACLINK driver has been m...
Currently, we are working on a project of a shortwave timing receiver (which can receive two signals at the same time, with frequencies of 15M/10M respectively). Two 15M/10M filters are required on th...
When I open a USB flash drive in CE5.0 and perform a write operation, the first call to WriteFile is always very slow and takes a long time to complete, but the second and subsequent calls are very fa...
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
Current
measurement:
Magnetic balance Hall current
sensor
is used
. The sensor can measure AC from DC to 100kHz.
In automatic measurement and control systems, it is often nec...[Details]
1. Introduction
AS-Interface bus technology is an intelligent network that uses a single cable to connect sensors and actuators to controllers, transmit data, and provide power. It can be used...[Details]
Applying fieldbus technology on new beer production lines is the first choice for large beer companies with strong management level and technical strength. Guangzhou Zhujiang Beer Group Co., Ltd. i...[Details]
In the development direction of the automotive industry, electric vehicles (EV) and hybrid electric vehicles (HEV) are becoming an obvious trend. From a technical point of view, hybrid power is mor...[Details]
The battery and its management system are one of the key technologies of electric vehicles. In the past few years, most companies have encountered embarrassment in the development of electric vehic...[Details]
The cruise control system (CCS) of a vehicle is also called a constant speed driving system. It is an electronic control device that uses advanced electronic technology to automatically adjust the ...[Details]
1 Overview
As a driving power source, the new battery has a range of more than 200 km within the acceptable weight range of the mass market, which provides an important way for power batteries...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
