805-007FPHBBZNUPA-72 datasheet, PDF

Datasheet> All Categories > The connector> The connector> 805-007FPHBBZNUPA-72

805-007FPHBBZNUPA-72: DescriptionInterconnection Device; CategoryThe connector The connector; File Size175KB，3 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

805-007FPHBBZNUPA-72 Overview

Interconnection Device

805-007FPHBBZNUPA-72 Parametric

Parameter Name	Attribute value
Reach Compliance Code	compliant
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

Series 80 “Mighty Mouse”

ASAP Cordsets For Ethernet, IEEE 1394 and USB 2.0

ASAP Cordsets For High Speed Serial Data

Upgrade commercial high speed

serial interconnects

to mil-spec

performance. Glenair’s ASAP “Mighty

Mouse” cordsets are available for

100BASE-T, Gigabit Ethernet, IEE

1394 and USB 2.0 applications.

These cordsets combine aerospace-

grade data cables with Series 80

“Mighty Mouse” harsh environment

connectors for maximum

performance and minimum size.

FEP jackets

meet FAA

flammability requirements. Or,

choose

low smoke / zero halogen

polyurethane jackets

for mass

transit or shipboard applications.

Three strain relief options –

Standard overmolded cables offer

excellent strain-relief and cable

sealing.Or, choose heatshrink boots

for smallest form factor. If repairability

and ruggedness are important, choose

machined aluminum EMI backshells.

100BASE-T Cordset

with 4 Pin Series 800 Connector

HOW TO ORDER CORDSETS

Step 1: Select the Connector Series

Table1 lists the ﬁve types of Series 80 connectors. For more information on

selecting a connector, please refer to the connector selection chart on the following

page. This section does not contain ordering information for series 802 “Aqua

Mouse” cordsets. Please contact Glenair for information on hazardous environment

high pressure cables for the 802 Series.

Step 2: Select the Cable

Table 2 contains speciﬁcations for standard data cables. The cable type also

determines the connector layout.

4 pin connectors are used for 4 wire cables,

and 10 pin connectors are used for 8 wire cables.

Step 3: Select a Cable Jacket

Table 3 shows available jacket options. Choose FEP ﬂourocarbon jackets

for airframe and avionics applications, or choose low smoke/zero halogen

polyurethane jackets for soldier systems, vehicles, and transit systems.

Step 4: Select a Cable-To-Connector Interface

Table 3 provides three ways to attach the cable to the connector:

1. Polyamide boot, overmolded with ﬂexible strain relief

2. Aluminum backshell, shielded, watertight and removable

3. Heat-shrink boot, low smoke/ zero halogen

Step 5: Select a Connector Conﬁguration

Table 1 shows connector codes for specifying plug versus receptacle and pin

versus socket contacts. Add a plating code, keying option and length.

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

K-1

Rev. 05-APR-2007

E-Mail: sales@glenair.com

Recommended Resources

7-axis motion and pressure sensor, did you know?

Differential bridge amplifier circuit diagram

Fuse blown centralized monitoring circuit 2

5 to 30 minute time limit controller circuit

JSJ type transistor time relay circuit (1)

Two-arm rectifier module three-phase bridge rectifier circuit

Why does the DC signal change so much before and after driving the LD after passing through the bias Tee circuit?: 50mA current drives LD, the output power of LD is 30uW. 50mA current drives LD through the bias Tee circuit, so the output power of LD should also be 30uW. Why does the power of LD increase 20 times a...; szyang Analog electronics

Serial communication related: Please give me some advice, thanks. . I have three questions: 1. Now RS232 serial port usually uses 9-frame connection line. The simplest connection is 3 connection lines, namely ground connection (co...; luoxianbo Embedded System

What is wrong with the following timer configuration? Why doesn't the timer interrupt occur?: void delay(); void timer0(void); unsigned int count; main(void) { InitSysCtrl(); DINT; IER=0x0000; IFR=0x0000; InitPieCtrl(); InitPieVectTable(); There is no problem with the above program, and other ...; jonny0811 Microcontroller MCU

[M4 development board Hanker trial mania] ddllxxrr 6: OTG mouse: The USB OTG mouse is tuned. It is implemented. I did not involve the detailed screen because I was in a hurry. My program uses the arrow keys of the development board as a mouse. When the development ...; ddllxxrr Microcontroller MCU

Problems with display driver migration when upgrading from wince5.0 to 6.0: Add Display driver, and compile correctly after modification. Finally, the image can be generated, but there is no display after downloading to the board. The transplant I made is the smallest kernel....; mengzhong163 Embedded System

Communication interface experiment: [align=left][color=black][font=宋体][size=10.5pt] [/size][/font][/color][color=black][font=宋体][size=10.5pt]Serial communication application experiment[/size][/font][/color][/align] [align=left][color=bl...; gina Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components