EEWORLDEEWORLDEEWORLD

Part Number

Search

8BUS8C22-094PW

Description
MIL Series Connector, 13 Contact(s), Aluminum Alloy, Male, Crimp Terminal, Plug,
CategoryThe connector    The connector   
File Size228KB,6 Pages
ManufacturerEsterline Technologies Corporation
Download Datasheet Parametric View All

8BUS8C22-094PW Overview

MIL Series Connector, 13 Contact(s), Aluminum Alloy, Male, Crimp Terminal, Plug,

8BUS8C22-094PW Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresSTANDARD: MIL-C-26482, POLARIZED
Back shell typeSOLID
Body/casing typePLUG
Connector typeMIL SERIES CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact point genderMALE
Coupling typeTHREADED
DIN complianceNO
empty shellNO
Filter functionNO
IEC complianceNO
MIL complianceYES
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeCABLE
OptionsGENERAL PURPOSE
Shell materialALUMINUM ALLOY
Housing size22
Termination typeCRIMP
Total number of contacts13
Base Number Matches1
8 BUS Series
Description
Applications
Bifilar BUS lines for multiplex
transmission
• High level RFI / EMI
• Rear removable contacts
• Two contact layouts
- shell 22 : 9 standard contacts + 4 BUS
- shell 24 : 41 standard contacts + 2 BUS
Standards
derivated from
MIL-C 26482 Series II
NFC 93422 HE 312
83723 Serie I
Characteristics
Mechanical
• Shell : aluminum alloy
• Insulator : thermoset
• Contacts : copper alloy
• Vibrations : 10 to 20 000 Hz,
acceleration 20g
• Shock : 100g, 6ms
Electrical
• Withstanding voltage : 1500 Vrms Max
• Current rating : 7,5 A
• Insulation resistance :
5000 MΩ
• Contact resistance : # 20 contact :
4 mΩ
bifilar inner contact :
4 mΩ
• Contact bifilar impedance at 3 GHz
- between central contacts : 68
- between central contacts and shielding
of the bifilar contact : 42
Climatic
• Temperature range : - 55°C to +125°C
• Endurance : 500 operations
• Sealing : immersion at low pressure :
33 mbar
• Resistance to salt spray : 48 hours
• Damp heat : 21 days or 10 cycles
according to MIL-STD 202 method 106
Ordering information
basic series
8 BUS
0
R
22 - 09
4
S
N
•••
0 -
square flange receptacle
(backnut or straight backshell)
6 -
plug with backnut or straight backshell
8 -
plug with elbow backshell
7 -
jam nut receptacle (backnut or straight backshell)
9 -
flange mounted plug with «Twist pull» backshell
R -
backnut
C -
cable clamp
O -
supplied without backshell
shell size
contacts # 20
22 or 24 -
(plug 9 C : shell 22 only)
09 -
shell 22
41 -
shell 24
4 -
shell 22
2 -
shell 24
P -
male contact
S -
female contact
bifilar shielded contacts
polarization
specifications
N -
normal, W and X (see table next page)
see table next page
366
Strange! Touching the crystal input pin of the microcontroller with your hand will make the microcontroller run
After writing the program into the MCU, the program does not run (the diode driven by port B does not light up); when I touch the crystal oscillator input pin of the MCU with my hand, the MCU can run....
XY Embedded System
Discussion on LED fluorescent lamp power supply design
LED fluorescent lamp power supply is very popular this year. Many companies design products that often have problems in the certification stage due to not understanding the specifications, and spend a...
led123 LED Zone
A pitfall in buying goods on a certain fish - BMW night vision camera
...
littleshrimp Integrated technical exchanges
Big Brother, please help
There is a USB detection. When the USB is detected, the red light in RGB will be displayed. When the key is pressed for the first time, it will light up white. There are five gears corresponding to fi...
陈其海 ADI Reference Circuit
PCB automatic routing failed
When I used the board wizard, I set the following rules to run two lines between two pads. However, after I finished the layout and routed, I found that my board components were a bit dense, and the t...
面纱如雾 PCB Design
Problems with adding vias to PCB boards
As the title says, for example, for a two-layer PCB After copper is applied to both the top GND and the bottom GND Why do we need to place several vias on the GND copper between the two layers? (After...
shaorc PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2656  2537  2864  1367  1675  54  52  58  28  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号