EEWORLDEEWORLDEEWORLD

Part Number

Search

S2BA1021ERA

Description
Array/Network Resistor, Isolated, Metal Film, 0.7W, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, CHIP, LEAD FREE
CategoryPassive components    The resistor   
File Size299KB,5 Pages
ManufacturerThin Film Technology Corp (TFT)
Environmental Compliance  
Download Datasheet Parametric View All

S2BA1021ERA Overview

Array/Network Resistor, Isolated, Metal Film, 0.7W, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, CHIP, LEAD FREE

S2BA1021ERA Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPRECISION
The first element resistor1020 Ω
JESD-609 codee3
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature175 °C
Minimum operating temperature-40 °C
Package shapeRECTANGULAR PACKAGE
method of packingTR
Rated power dissipation(P)0.7 W
Rated temperature125 °C
Resistor typeARRAY/NETWORK RESISTOR
surface mountYES
technologyMETAL FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin (Sn)
Terminal shapeWRAPAROUND
Tolerance0.1%
Base Number Matches1
SR02 & S2 (Published)
Page 1 of 5
Precision Resistor Networks
SR02
& S2 Series
Description
The
SR02
& S2 Series resistor networks are precision-class metal film components featuring tight resistance
tolerance and low values of temperature coefficient of resistance (TCR). This resistor network package
provides both excellent resistance ratio and TCR tracking.
Electrical
Parameter
Resistance range
Resistance ratio
tolerance:
Power rating per
package
Operating
temperature
Storage temperature
Power Derating Curve
Tolerance Table
Resistance Value
Range
10Ω - <20Ω
20Ω - <100Ω
100Ω -<15KΩ
SR02
& S2 series
10Ω - 30KΩ
(See Tolerance Table below
for further details)
±0.02% (Q)
±0.05% (A)
0.70 watts @125°C
(refer to derating curve)
- 40 to +175°C
- 55 to +125°C
Abs.
Resistance
Tolerance
Available
±0.05% (A)
±0.10% (B)
±0.02% (Q)
±0.05% (A)
±0.10% (B)
±0.01% (T)
±0.02% (Q)
±0.05% (A)
±0.10% (B)
±0.01% (T)
±0.02% (Q)
±0.05% (A)
±0.10% (B)
Absolute TCR TCR Tracking
Tolerance
(ppm.°C)
(refer to note
Available
1& 2)
±25 ppm/°C
±5 (M)
(E)
±25 ppm/°C(E)
±2 (R)
±5 (M)
±5 ppm/°C (M)
±1 (X)
±2 (R)
±10 ppm/°C
±5 (M)
(Y)
±25 ppm/°C
(E)
±10 ppm/°C
±2 (R)
(Y)
±5 (M)
±25 ppm/°C
(E)
Note 1:
Ratio values greater
than 50:1 only available in ±5
ppm/°C TCR tracking
tolerance
Note 2 :
±1ppm/°C TCR
tracking only available for
identical resistance values.
15KΩ - Max
Mechanical
http://www.thin-film.com/web/tft.nsf/41acb363040f5be585256a7b001dcc4c/b48916af35... 10/23/2007
MP2459 related circuit solution
I recently used MP2459. The datasheet says that the enable pin pull-up is effective. I want to ask what is the role of R4 in the example it gives? Can it be directly connected to R5100k? What is the d...
CcKk Power technology
What is the difference between analog IC design and IC design using VHDL language?
I feel that analog IC design should be to design analog circuits, design op amps, etc., and then build TTL, CMOS, etc. on silicon wafers to make IC chips; but I often see that IC design is to design I...
wn1983 Embedded System
TI Industrial Robots Online Seminar Resource Sharing
Main Agenda of the Seminar 1. Provide a detailed introduction to the definition and classification, system considerations, and module analysis of industrial robots; 2. Count the challenges faced in in...
arui1999 Robotics Development
【Signal processing】:FPGA implements DSP (digital signal processing technology)
[[i]This post was last edited by liuceone on 2011-12-10 17:30[/i]]...
liuceone FPGA/CPLD
I need help from forum friends to confirm whether the LCD12864 LCD serial driver using the ST7920 controller can read back the display data?
I have been using the LaunchPad G2553 board to write the LCD12864 display driver in 8-bit parallel mode. Now the functions are almost sufficient, so I want to expand some functions, but I find that th...
bobde163 Microcontroller MCU
Can small and medium-sized chips (40, 74, etc.) be controlled by VCC and GND? If VCC and GND are not added, will the circuit be affected if other pins are added to the circuit?
I want to use serial control for some chips. Can I use vcc and gnd to control them? The signal lines are connected in parallel. I use vcc and gnd to control whether they are connected or not. I think ...
SPEED Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 889  2294  1638  671  861  18  47  33  14  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号