The AS29F002 is a 2 megabit, 5 volt only Flash memory organized as 256K bytes of 8 bits each. For flexible erase and program capability, the 2
megabits of data is divided into 7 sectors: one 16K byte, two 8K byte, one 32K byte, and three 64K bytes. The data appears on DQ0–DQ7. The
AS29F002 is offered in JEDEC standard 40-pin TSOP, 32-pin PLCC, 32-pin TSOP, and 32-pin PDIP packages. This device is designed to be
programmed and erased in-sytem with a single 5.0V V
CC
supply. The device can also be reprogrammed in standard EPROM programmers.
The AS29F002 offers access times of 55/70/90/120 ns, allowing 0-wait state operation of high speed microprocessors. To eliminate bus contention
the device has separate chip enable (CE), write enable (WE), and output enable (OE) controls.
The AS29F002 is fully compatible with the JEDEC single power supply Flash standard. Write commands to the command register using standard
microprocessor write timings. An internal state-machine uses register contents to control the erase and programming circuitry. Write cycles also
internally latch addresses and data needed for the programming and erase operations. Read data from the device in the same manner as other Flash or
EPROM devices. Use the program command sequence to invoke the automated on-chip programming algorithm that automatically times the
program pulse widths and verifies proper cell margin. Use the erase command sequence to invoke the automated on-chip erase algorithm that
preprograms the sector if it is not already programmed before executing the erase operation, times the erase pulse widths, and verifies proper cell
margin.
Boot sector architecture enables the device to boot from either the top (AS29F002T) or bottom (AS29F002B) sector. Sector erase architecture allows
specified sectors of memory to be erased and reprogrammed without altering data in other sectors. A sector typically erases and verifies within 1.6
seconds. Hardware sector protection disables both program and erase operations in all or any combination of the seven sectors. The device provides
background erase with Erase Suspend, which puts erase operations on hold to read data from a sector that is not being erased. The chip erase
command will automatically erase all unprotected sectors.
A factory shipped AS29F002 is fully erased (all bits = 1). The programming operation sets bits to 0. Data is programmed into the array one byte at a
time in any sequence and across sector boundaries. A sector must be erased to change bits from 0 to 1. Erase returns all bytes in a sector to the erased
state (all bits = 1). Each sector is erased individually with no effect on other sectors.
The device features single 5.0V power supply operation for both read and write functions. Internally generated and regulated voltages are provided
for the program and erase operations. A low V
CC
detector automatically inhibits write operations during power transtitions. DATA polling of DQ7 or
toggle bit (DQ6) may be used to detect end of program or erase operations. The device automatically resets to the read mode after program/erase
operations are completed.
The AS29F002 resists accidental erasure or spurious programming signals resulting from power transitions. Control register architecture permits
alteration of memory contents only after successful completion of specific command sequences. During power up, the device is set to read mode
with all program/erase commands disabled when V
CC
is less than V
LKO
(lockout voltage). The command registers are not affected by noise pulses of
less than 5 ns on OE, CE, or WE. CE and WE must be logical zero and OE a logical one to initiate write commands.
When the device’s hardware RESET pin is driven low, any program/erase operation in progress will be terminated and the internal state machine will
be reset to read mode. If the RESET pin is tied to the system reset circuitry and a system reset occurs during an automated on-chip program/erase
algorithm, data in address locations being operated on will become corrupted and require rewriting. Resetting the device enables the system’s
microprocessor to read boot-up firmware from the Flash memory.
)/$6+
The AS29F002 uses Fowler-Nordheim tunnelling to electrically erase all bits within a sector simultaneously. Bytes are programmed one at a time
using EPROM programming mechanism of hot electron injection.
Some leaders went to a certain place for a meeting. The local custom was to have steamed bread, porridge and an egg . One morning, a leader peeled an egg and found it was bad. He said to the waitress,...
[color=#000][font=Arial, Helvetica, sans-serif]When using this solution, you only need to keep the light powered on and open the corresponding mobile phone LED light control software to establish a co...
Texas Instruments (TI) of the United States has launched the "TMS320TCI6487" DSP for baseband processing for GSM, WiMAX, and TD-SCDMA base stations. This product integrates three 1GHz DSP cores "C64x+...
Download (591.53 KB)
2011-3-2 10:29What is the general reason? I use discrete components to make Class A and B power amplifiers. The output voltage waveform of the pre-driver stage is normal, but the ...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
1. Introduction
This design was made for participating in an electronic design competition. It effectively solved the problem of the operation and control of an electric car on a seesaw. The s...[Details]
With the advent of increasingly powerful processors, image sensors, memory, and other semiconductor devices, as well as the algorithms that enable them, computer vision can be implemented in a wide...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
As people's requirements for safety and comfort in the process of driving cars continue to increase, automotive radars are widely used in the car's adaptive cruise system, collision avoidance syste...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
Some people think: as long as the program runs well, it doesn't matter how the original program is written. But this is absolutely not the case. Software is not completed in one go, and it is neces...[Details]
In view of the price and performance differentiation of Chinese home video intercom and security products, this paper analyzes
the design of smart terminals based
on a Chinese original
...[Details]
As the global leader in virtual instrument technology, NI provided customers with more than 6,000,000 virtual instrument measurement devices in 2004 alone. For 25 years, engineers have used virtual...[Details]
Liquid crystal displays are increasingly widely used in pocket instruments and low-power application systems due to their advantages of low power consumption, small size, rich display content, and ...[Details]
UPS is an uninterruptible power supply (UPS). This device can ensure that after a power outage in the computer system, users can continue to work for a period of time and save files urgently, witho...[Details]
Thyristor is the abbreviation of thyristor, commonly known as silicon controlled rectifier. It is a high-power switching semiconductor device, represented by the letter symbols "V" or "VT" in the c...[Details]
What is Power Monitoring Software
Power monitoring software is used in conjunction with an uninterruptible power supply (UPS) to improve its performance. When using an UPS, users can use this ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
