EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SLAFA2642

Description
Transponder, FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-SLAFA2642 Overview

Transponder, FC/UPC Connector,

PH1-SLAFA2642 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsOC-192, SONET
Connection TypeFC/UPC CONNECTOR
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1530 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
Base Number Matches1
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
TI's top 10 RS-485 design tips
[align=left]Do you often come across this question: Are there some tips or tricks to know when designing with RS-485? [/align][align=left]The following is a comprehensive and comprehensive list of imp...
maylove Analogue and Mixed Signal
Vcom of a fully differential amplifier
As the title says, Vcom is only related to the output and is the common-mode voltage of the output. Is this parameter the input range of a single-ended signal or the input range after averaging the si...
呜呼哀哉 Analog electronics
Has anyone used CYPRESS's PSOC?
As the title says, a salesperson came recently and gave a speech. I can’t just listen to one side of the story, so I came to the forum to ask....
sjl2001 MCU
Forum Level Suggestions
Our forum level is all based on prestige, which is a bit unreasonable. I suggest that we consider it comprehensively based on the number of posts, prestige and core coins.This is the only way to stimu...
laoguo Suggestions & Announcements
I'm new here, please help me. Why does the software interface look like this after I open the CCS5.2 I installed?
This is what it looks like when I open it. This is my first time using this and I really don't know how to start. Is there something wrong with my installation?...
吃包子的大猪 Microcontroller MCU
Verlog program.zip
Verlog Program...
白丁 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 569  2400  895  1842  2768  12  49  19  38  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号