MN42D0350 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> MN42D0350

MN42D0350: DescriptionRF N Connector, Cable Mount; CategoryThe connector The connector; File Size194KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

MN42D0350 Overview

RF N Connector, Cable Mount

MN42D0350 Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
Other features	APPLICABLE CABLES:RG 59; RG 59A; RG 59B; RG 62; RG 62AU
Characteristic impedance	50 Ω
Connector type	RF N CONNECTOR
Contact to complete cooperation	NOT SPECIFIED
Coupling type	THREADED
DIN compliance	NO
Filter function	NO
IEC compliance	NO
insulator material	DELRIN
MIL compliance	NO
Manufacturer's serial number	N
Installation method	STRAIGHT
Installation type	CABLE
Maximum operating frequency	4 GHz
Panel mounting	NO
voltage standing wave ratio	1.2
Base Number Matches	1

Preview

Download Datasheet

View All

Our years of experience translates to immediate support for

™

existing or new project development. Continued commitment

to technological advancement assures our customers access

to the latest developments available.

N Series

Applications:

Transmitters and Receivers, Broadcast Equipment, Antenna,

LANs, Test and Measurement

*Electrical Specifications:

Voltage Rating:

Withstanding Voltage:

Insulation Resistance:

Contact Resistance:

VSWR:

Frequency Range:

Impedance:

AC 500V

AC 1000V one minute

1000 MΩ min at DC 500V

3 mΩ max at DC 1A

1.2 max 0-4 GHz

0-4000 MHz

50 Ohm

DIN 7/16 Series

Applications:

Broadcast Communications, Control Components, Cellular Base

Stations, Jumper Cables

*Electrical Specifications:

Voltage Rating:

Withstanding Voltage:

Insulation Resistance:

Contact Resistance:

VSWR:

Frequency Range:

Impedance:

2.7 kV RMS

4 kV RMS

10 GΩ min

8 mΩ After Conditioning

1.02 max 0-7 GHz

DC-7 GHz

50 Ohm

UHF Series

Applications:

CB Radios, Antennas, Public Address Systems, Landing Systems,

Ground Control Apparatus

*Electrical Specifications:

Voltage Rating:

Withstanding Voltage:

Insulation Resistance:

Contact Resistance:

Frequency Range:

Impedance

AC 500V

AC 1000V one minute

1000 MΩ min at DC 500V

3 mΩ max at DC 1A

0-300 MHz

Non-Constant

*These characteristics are typical and may not apply to all connectors

9 0 9 R a h w a y A v e . , U n i o n , N J 0 7 0 8 3 - 5 4 9 1 . Te l : 9 0 8 . 6 8 8 . 8 0 0 0 . F a x : 9 0 8 . 6 8 8 . 8 0 5 3 . E m a i l : I n f o @ m e t h o d e r f . c o m

Recommended Resources

USB interface circuit of Newman MP4 machine

HT-821A0 circuit

digital stopwatch circuit

Autotransformer manual starting control circuit

Standard application circuit diagram of MAX742

PIN diode attenuator

Synchronization of asynchronous clock signals: In asynchronous design, signal synchronization is necessary to prevent metastable states. The synchronization of single-bit signals is usually done by clock latching. From the perspective of asynchron...; eeleader FPGA/CPLD

Is anyone working on .NET Micro Framework?: Where can I find a good tutorial? http://msdn2.microsoft.com/en-us/embedded/bb267253.aspx...; steve Embedded System

Is there an official reference routine for the C6748 PRU?: A few questions 1 The downloaded C6748 StartWare does not contain PRU routines. Does TI have any official reference routines in this regard? 2 Is there a separate PDF document or information with more...; 灞波儿奔 DSP and ARM Processors

Demonstration of the basics of high-speed PCB: [i=s]This post was last edited by Tianming on 2014-7-18 15:58[/i] [font=Arial, Helvetica, sans-serif][color=#454b57][size=12px]The video demonstration will examine two sets of functionally identical P...; 天明 ADI Reference Circuit

Design of reset circuit for single chip microcomputer: MCU reset circuit design (from http://www.hpoo.ne ) 1. Overview The factors that affect the stability of the operation of the single-chip system can be roughly divided into two parts: external factors...; tiankai001 Energy Infrastructure?

[Q&A] Q: When looking at digital isolator data sheets, I am confused by the use of Mbps. Why not MHz?: [color=#247ab5][font=Arial, Helvetica, sans-serif][b]Q: When looking at digital isolator data sheets, I am confused by the use of Mbps. Why not MHz? [/b][/font][/color]...; 雨中 ADI Reference Circuit

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components