The ACT-F2M32A is packaged in a hermetically sealed co-fired ceramic 68 lead, .94"
SQ Ceramic Gull Wing CQFP package. This allows operation in a military environment
temperature range of -55°C to +125°C.
The ACT-F2M32A can be programmed (both read and write functions) in-system using
the +5.0V V
CC
power supply. A 12.0V V
PP
is not required for programming or erase
operations. The end of program or erase is detected by the RY/BY pin, Data Polling of
DQ7, or by the Toggle bit (DQ6).
The ACT-F2M32A also has a hardware RESET pin. When this pin is driven low,
execution of any Embedded Program Alggorithm or Embedded Erase Algorithm will be
terminated.
Each block can be independently erased and programmed 100,000 times at +25°C.
For Detail Information regarding the operation of the Am29F016 Sector Erase Flash
Memory, see the AMD datasheet (Publication 18805).
Aeroflex Circuit Technology
2
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
Absolute Maximum Ratings
Parameter
Case Operating Temperature Range
Storage Temperature Range
Voltage with Respect to GND (All pins except A
9)
(1)
Voltage on Pins A
9,
OE, RESET
(3)
(2)
Range
-55 to +125
-65 to +150
-2.0 to +7.0
-2.0 to +13.5
-2.0 to +7.0
200
Units
°C
°C
V
V
V
mA
Vcc Supply Voltage with Respect to Ground
(1)
Output Short Circuit Current
Notes:
1. Minimum DC voltage is -0.5V on input/output pins. During Transitions, inputs may undershoot GND to -2.0V for periods up to 20ns. Maximum DC voltage on
input/output pins is V
CC
+ 0.5V, which may overshoot to V
CC
+ 2.0V for periods up to 20ns.
2. Minimum DC input voltage on A
9
,OE, RESET pins is -0.5V. During Voltage transitions, A
9
, OE & RESET may overshoot GND to -2.0V for periods up to 20ns.
Maximum DC input voltage on A
9
is +12.5V which may overshoot to 14V for periods up to 20ns.
3. No more than one output shorted to ground for no more than 1 second.
NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating only; functional
operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions" may effect device reliability.
Recommended Operating Conditions
Symbol
V
CC
V
IH
V
IL
T
C
Parameter
5V Power Supply Voltage (10%)
Input High Voltage (CMOS)
Input Low Voltage
Operating Temperature (Military)
Minimum
+4.5
0.7 x V
CC
-0.5
-55
Maximum
+5.5
V
cc
+ 0.3
+0.8
+125
Units
V
V
V
°C
Capacitance
(f = 1MHz, T
C
= 25°C, Standard Configuration)
Symbol
C
AD
C
OE
C
CE
C
RESET
C
WE
C
RY
/
BY
C
I
/
O
Parameter
A0 – A20 Capacitance
OE Capacitance
CE Capacitance
RESET Capacitance
WE Capacitance
RY/BY Capacitance
I/O0 – I/O31 Capacitance
Maximum
50
50
20
50
60
50
20
Units
pF
pF
pF
pF
pF
pF
pF
Capacitance Guaranteed by design, but not tested.
DC Characteristics – CMOS Compatible
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Input Load Current
A9 Leakage Current
Output Leakage Current
Vcc Active Read Current
Vcc Active Program/Erase Current
(1)
Vcc Standby Current
Vcc Standby Current (Reset)
Output Low Voltage
Output High Voltage
Sym
I
IL
I
LIT
I
LO
I
CC
1
I
CC
2
I
CC
3
I
CC
4
V
OL
V
OH
1
V
OH
2
Conditions
V
CC
= V
CC
Max., V
IN
= V
CC
or GND
V
CC
= V
CC
Max., A9 = +12V
V
CC
= V
CC
Max., V
IN
= GND to V
CC
CE = V
IL
, OE = V
IH
CE = V
IL
, OE = V
IH
V
CC
= V
CC
Max., CE = RESET = V
CC
± 0.3V
V
CC
= V
CC
Max., RESET = V
CC
± 0.3V
V
CC
= V
CC
Min., I
OL
= 12 mA
V
CC
= V
CC
Min., I
OH
= -2.5 mA
V
CC
= V
CC
Min., I
OH
= -100 µA
Min
Max
10
50
10
160
240
4
4
0.45
Units
µA
µA
µA
mA
mA
mA
mA
V
V
V
0.85 x
V
CC
V
CC
-
0.4V
3.2
4.2
Low V
CC
Lock-Out Voltage
Notes:
1. Not 100% tested.
Aeroflex Circuit Technology
V
LKO
V
3
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
AC Characteristics – Write/Erase/Program Operations – WE Controlled
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Parameter
Write Cycle Time
Address Setup to WE Going Low
Address Hold Time from CE High
Data Setup to WE Going High
Data Hold Time from WE High
Output Enable Hold Time
Read Recover Time Before Write
(OE High to WE Low)
CE Setup Time from WE Low
CE Hold Time from WE High
WE Pulse Width
WE Pulse Width High
Byte Programming Operation
Sector Erase Operation
V
CC
Set-Up Time
Rise Time to V
ID
OE Setup Time to WE Active
Reset Pulse Width
Program/Erase Valid to RY/BY
Delay
Notes:
1. Not 100% tested.
Parameter
Symbol
JEDEC
t
AVAV
t
AVWL
t
WLAX
t
DVWH
t
WHDX
90ns
Min
90
0
45
45
0
0
10
Max
120ns
Min
120
0
50
50
0
0
10
0
0
0
50
20
8
Max
150ns
Min
150
0
50
50
0
0
10
0
0
0
50
20
8
Max
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
15
50
500
4
500
60
Sec
µs
ns
µs
ns
ns
Symbol
Standard
t
WC
t
AS
t
AH
t
DS
t
DH
Read
Toggle Bit I and Data Polling
t
OEH
t
GHWL
t
CS
t
CH
t
WP
t
WPH
t
WHWH
1
t
WHWH
2
t
VCS
t
VIDR
t
GHWL
t
ELWL
t
WHEH
t
WLWH
t
WHWL
t
WHWH
1
t
WHWH
2
0
0
0
45
20
8
15
50
500
4
500
40
15
50
500
4
500
50
t
OESP
t
RP
t
BUSY
AC Characteristics – Read Only Operations
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Parameter
Read Cycle Time
(1)
Parameter
Symbol
JEDEC
t
AVAV
t
AVQV
t
ELQV
t
GLQV
t
EHQZ
t
GHQZ
t
AXQX
0
90ns
Min
90
90
90
40
20
20
Max
120ns
Min
120
120
120
50
30
0
0
30
Max
150ns
Min
150
150
150
55
35
0
0
35
Max
Units
ns
ns
ns
ns
ns
ns
ns
20
µs
Symbol
Standard
t
RC
t
ACC
t
CE
t
OE
t
DF
t
DF
t
OH
t
READY
Address to Output Delay
CE to Output Delay
OE to Output Delay
CE to Output in High Z
(1)
OE to Output in High Z
(1)
Output Hold from Addresses, CE or OE Change, Whichever Occurs
First
RESET Low to Read Mode
(1)
Notes:
1. Not 100% tested.
20
20
Aeroflex Circuit Technology
4
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
AC Characteristics – Write/Erase/Program Operations – CE Controlled
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Parameter
Write Cycle Time
(1)
Parameter
Symbol
JEDEC
t
AVAV
t
AVEL
t
ELAX
t
DVEH
t
EHDX
90ns
Min
90
0
45
45
0
0
0
10
Max
120ns
Min
120
0
50
50
0
0
0
10
0
0
0
50
20
8
Max
150ns
Min
150
0
50
50
0
0
0
10
0
0
0
50
20
8
Max
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
15
Sec
Symbol
Standard
t
WC
t
AS
t
AH
t
DS
t
DH
t
OES
Read
Toggle Bit I and Data Polling
t
OEH
t
GHEL
t
WS
t
WH
t
CP
t
CPH
t
WHWH
1
t
WHWH
2
Address Setup to CE Going Low
Address Hold Time from CE Low
Data Setup to CE Going High
Data Hold Time from CE High
Output Enable Setup Time
(1)
Output Enable Hold Time
(1)
Read Recover Time Before Write
(OE High to WE Low)
CE Setup Time from WE Low
WE Hold Time from CE High
WE Pulse Width
WE Pulse Width High
Byte Programming Operation
Sector Erase Operation
Notes:
1. Not 100% tested.
t
GHEL
t
WLEL
t
EHWH
t
ELEH
t
ELEL
t
WHWH
1
t
WHWH
2
0
0
0
45
20
8
15
15
Aeroflex Circuit Technology
5
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
STM32F105 USB cannot be recognized. When using 25M, the UART1 TX pin needs to be pulled high (vUSB). When using 8M crystal, it is not needed. Therefore, only 8M crystal can be used when using at the s...
S32K is the hottest automotive controller product this year. It has migrated from 8/16bit/PowerPC to ARM Cortex architecture, and is the future of general-purpose MCUs. Brother En will talk to you abo...
I am sorry to trouble you all again.
As shown in the figure, the left side is the USB-B interface, and a TVS protection device in a SOT23-6 package is added. Now the lengths of the two USB cables are ...
With the development of science and the continuous innovation of microelectronics technology, the application of embedded systems is increasing and has been widely penetrated into various fields. Em...
1. Broadcasting and communication (36) GB/T1418-1995 General text symbols for telecommunication equipment GB/T14733.1-93 Telecommunication terminology Telecommunication, channel and network SHJ28-90 S...
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
The above is to use MB1404 as a stereo composite signal transmitter. You can use the internal high-frequency amplifier and oscillator or not! According to my experience, I still recommend beginners...[Details]
Cars equipped with xenon headlights are already common on the road. Whether they are standard equipment on high-end cars or embellishments on modified cars, xenon lamps are gradually becoming a sym...[Details]
1 Overview
In the field of traditional lighting, the concepts and definitions of lamps and lamps are clear. Lamps and lamps have their own applicable product standards, supporting technical st...[Details]
The power supply is the core component of a computer. Although it is not of high value, all computer components rely on the switching power adapter to provide energy, so the stability of a power su...[Details]
1 Introduction to the overall system solution
The hardware part is mainly used to amplify the sound. When the sound is loud enough, the signal can be introduced into the microcontroller for de...[Details]
There are many types and styles of digital voltmeters in design and development. Traditional digital voltmeters have their own characteristics. They are suitable for manual measurement on site. Tra...[Details]
Introduction
Temperature and humidity control are widely used in people's production and life. People use thermometers and hygrometers to collect temperature and humidity, and control temperatu...[Details]
TMC428 is a stepper motor motion controller from TRINAMIC. It can reduce the workload of motor control software design and development costs. The 3-axis stepper motor drive control system based on ...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
