EEWORLDEEWORLDEEWORLD

Part Number

Search

BU-63149F4-280L

Description
Line Driver/Receiver, 2 Driver, Hybrid, CDFP36
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size65KB,8 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BU-63149F4-280L Overview

Line Driver/Receiver, 2 Driver, Hybrid, CDFP36

BU-63149F4-280L Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
package instructionDFP, FL36,.8,100
Reach Compliance Codecompliant
ECCN codeEAR99
Differential outputYES
Number of drives2
High level input current maximum value0.0001 A
JESD-30 codeR-XDFP-F36
JESD-609 codee0
Number of terminals36
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Minimum output swing18 V
Maximum output low current0.0034 A
Package body materialCERAMIC
encapsulated codeDFP
Encapsulate equivalent codeFL36,.8,100
Package shapeRECTANGULAR
Package formFLATPACK
power supply5 V
Maximum receive delay
Maximum slew rate565 mA
Nominal supply voltage5 V
surface mountYES
technologyHYBRID
Temperature levelINDUSTRIAL
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
Base Number Matches1
BU-63147 and BU-63149
MIL-STD-1553 DATA BUS
+5V TRANSCEIVER
DESCRIPTION
The BU-63147/49 transceiver is a com-
plete dual transmitter and receiver pair
conforming fully to MIL-STD-1553A
and 1553B. Features include: mono-
lithic design, +5V power supply voltage,
Harris or Smiths type decoder inter-
face, completely independent dual
redundant operation, and small size
(36 pin DIP). The receiver section of
the BU-63147/49 series accepts
phase-modulated bipolar data from a
MIL-STD-1553 Data Bus and pro-
duces TTL Signal data at its output.
RX DATA OUT and
RX DATA OUT
These outputs represent positive and
negative variations of the input data
signals beyond an internally fixed
threshold level. An external STROBE
input enables or disables the receiver’s
outputs.
The transmitter section accepts
bi-phase TTL signal data at its
TX DATA IN and
TX DATA IN
inputs
and produces phase-modulated
bipolar data at the TX DATA OUT and
TX DATA OUT
outputs.
The
transmitter’s output voltage level is
typically about 11Vpp. An external
input, INHIBIT, takes priority over the
transmitter inputs and disables the
transmitter when activated with a logic
“1”.
The small size, +5V power supply volt-
age,
and
compliance
with
MIL-STD-1553 simplify engineering
design, making it an excellent choice
for interfacing with any MIL-STD-1553
system.
FEATURES
+5V Power Supply
Low Power
Conforms Fully To MIL-STD-1553A
AND 1553B
Dual Transceiver
Available with MIL-STD-1760
Compliant Transmitter Voltage
Available with McAir Compatible
Waveform
36-Pin DIP
HARRIS or SMITHS I/O
Compatibility
+5 V
1553
DATA
BUS
RECEIVER STROBE
BI PHASE
TTL DATA
COMPARATOR
RX DATA OUT
RX DATA OUT
DECODER
PHASE MODULATED
BIPOLAR DATA
RX DATA IN
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX DATA IN
RECEIVER SECTION
FILTER
FILTER
COMPARATOR
TRANSMITTER SECTION
TX Data Out
SHAPING
NETWORK
TX DATA IN
TX Data Out
SHAPING
NETWORK
ENCODER
TX DATA IN
CASE/GND
TX INHIBIT
FIGURE 1. BU-63147/49 BLOCK DIAGRAM
(one
channel shown)
©
2000
Data Device Corporation
N ways to play with an LED (Part 8) - unorthodox methods
N ways to play with an LED ( Part 8 ) - unorthodox methods Author: chenzhufly Email: chenzhufly@126.com 2010-05-11I have learned a lot along the way, from the simplest to the most complex. For example...
chenzhufly NXP MCU
Problems of communication between microcontroller and PC through wireless network card in wireless network
I want to realize wireless communication between multiple MCUs and a PC (through a wireless network card). If anyone has done this kind of development, please give me some advice. Note: The MCU is a h...
KESKY Embedded System
Passthru debugging is fine, but running it directly will cause a crash
I used windbg to set breakpoints, and after I walked through them step by step without any problems, I removed all the breakpoints, and there was no problem. However, if I do not enter debug mode and ...
virtualqwer Embedded System
Have you ever used tapered inductors?
I recently read an article about this, but I haven't used it before, so I came here to ask for adviceThis is a common fan shape.I made one and compared it with the normal one and found that there is n...
btty038 RF/Wirelessly
MSP430 download unknown devices problem solved
When using the emulator eZ-FET-lite that comes with launchpad, I found that I failed to download the development board and promptederrorconnecting to the target: unknown device! When using UNIflash to...
Aguilera Microcontroller MCU
Serial port debugging problem troubleshooting
[i=s]This post was last edited by zhangcaiqian on 2015-12-29 11:28[/i] I wrote a simple serial port file with a very simple function. It just returns the received serial port message. After writing it...
zhangcaiqian FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 863  101  161  774  813  18  3  4  16  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号