The ACT-F2M32A is packaged in a hermetically sealed co-fired ceramic 68 lead, .94"
SQ Ceramic Gull Wing CQFP package. This allows operation in a military environment
temperature range of -55°C to +125°C.
The ACT-F2M32A can be programmed (both read and write functions) in-system using
the +5.0V V
CC
power supply. A 12.0V V
PP
is not required for programming or erase
operations. The end of program or erase is detected by the RY/BY pin, Data Polling of
DQ7, or by the Toggle bit (DQ6).
The ACT-F2M32A also has a hardware RESET pin. When this pin is driven low,
execution of any Embedded Program Alggorithm or Embedded Erase Algorithm will be
terminated.
Each block can be independently erased and programmed 100,000 times at +25°C.
For Detail Information regarding the operation of the Am29F016 Sector Erase Flash
Memory, see the AMD datasheet (Publication 18805).
Aeroflex Circuit Technology
2
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
Absolute Maximum Ratings
Parameter
Case Operating Temperature Range
Storage Temperature Range
Voltage with Respect to GND (All pins except A
9)
(1)
Voltage on Pins A
9,
OE, RESET
(3)
(2)
Range
-55 to +125
-65 to +150
-2.0 to +7.0
-2.0 to +13.5
-2.0 to +7.0
200
Units
°C
°C
V
V
V
mA
Vcc Supply Voltage with Respect to Ground
(1)
Output Short Circuit Current
Notes:
1. Minimum DC voltage is -0.5V on input/output pins. During Transitions, inputs may undershoot GND to -2.0V for periods up to 20ns. Maximum DC voltage on
input/output pins is V
CC
+ 0.5V, which may overshoot to V
CC
+ 2.0V for periods up to 20ns.
2. Minimum DC input voltage on A
9
,OE, RESET pins is -0.5V. During Voltage transitions, A
9
, OE & RESET may overshoot GND to -2.0V for periods up to 20ns.
Maximum DC input voltage on A
9
is +12.5V which may overshoot to 14V for periods up to 20ns.
3. No more than one output shorted to ground for no more than 1 second.
NOTICE: Stresses above those listed under "Absolute Maximums Rating" may cause permanent damage to the device. These are stress rating only; functional
operation beyond the "Operation Conditions" is not recommended and extended exposure beyond the "Operation Conditions" may effect device reliability.
Recommended Operating Conditions
Symbol
V
CC
V
IH
V
IL
T
C
Parameter
5V Power Supply Voltage (10%)
Input High Voltage (CMOS)
Input Low Voltage
Operating Temperature (Military)
Minimum
+4.5
0.7 x V
CC
-0.5
-55
Maximum
+5.5
V
cc
+ 0.3
+0.8
+125
Units
V
V
V
°C
Capacitance
(f = 1MHz, T
C
= 25°C, Standard Configuration)
Symbol
C
AD
C
OE
C
CE
C
RESET
C
WE
C
RY
/
BY
C
I
/
O
Parameter
A0 – A20 Capacitance
OE Capacitance
CE Capacitance
RESET Capacitance
WE Capacitance
RY/BY Capacitance
I/O0 – I/O31 Capacitance
Maximum
50
50
20
50
60
50
20
Units
pF
pF
pF
pF
pF
pF
pF
Capacitance Guaranteed by design, but not tested.
DC Characteristics – CMOS Compatible
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Input Load Current
A9 Leakage Current
Output Leakage Current
Vcc Active Read Current
Vcc Active Program/Erase Current
(1)
Vcc Standby Current
Vcc Standby Current (Reset)
Output Low Voltage
Output High Voltage
Sym
I
IL
I
LIT
I
LO
I
CC
1
I
CC
2
I
CC
3
I
CC
4
V
OL
V
OH
1
V
OH
2
Conditions
V
CC
= V
CC
Max., V
IN
= V
CC
or GND
V
CC
= V
CC
Max., A9 = +12V
V
CC
= V
CC
Max., V
IN
= GND to V
CC
CE = V
IL
, OE = V
IH
CE = V
IL
, OE = V
IH
V
CC
= V
CC
Max., CE = RESET = V
CC
± 0.3V
V
CC
= V
CC
Max., RESET = V
CC
± 0.3V
V
CC
= V
CC
Min., I
OL
= 12 mA
V
CC
= V
CC
Min., I
OH
= -2.5 mA
V
CC
= V
CC
Min., I
OH
= -100 µA
Min
Max
10
50
10
160
240
4
4
0.45
Units
µA
µA
µA
mA
mA
mA
mA
V
V
V
0.85 x
V
CC
V
CC
-
0.4V
3.2
4.2
Low V
CC
Lock-Out Voltage
Notes:
1. Not 100% tested.
Aeroflex Circuit Technology
V
LKO
V
3
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
AC Characteristics – Write/Erase/Program Operations – WE Controlled
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Parameter
Write Cycle Time
Address Setup to WE Going Low
Address Hold Time from CE High
Data Setup to WE Going High
Data Hold Time from WE High
Output Enable Hold Time
Read Recover Time Before Write
(OE High to WE Low)
CE Setup Time from WE Low
CE Hold Time from WE High
WE Pulse Width
WE Pulse Width High
Byte Programming Operation
Sector Erase Operation
V
CC
Set-Up Time
Rise Time to V
ID
OE Setup Time to WE Active
Reset Pulse Width
Program/Erase Valid to RY/BY
Delay
Notes:
1. Not 100% tested.
Parameter
Symbol
JEDEC
t
AVAV
t
AVWL
t
WLAX
t
DVWH
t
WHDX
90ns
Min
90
0
45
45
0
0
10
Max
120ns
Min
120
0
50
50
0
0
10
0
0
0
50
20
8
Max
150ns
Min
150
0
50
50
0
0
10
0
0
0
50
20
8
Max
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
15
50
500
4
500
60
Sec
µs
ns
µs
ns
ns
Symbol
Standard
t
WC
t
AS
t
AH
t
DS
t
DH
Read
Toggle Bit I and Data Polling
t
OEH
t
GHWL
t
CS
t
CH
t
WP
t
WPH
t
WHWH
1
t
WHWH
2
t
VCS
t
VIDR
t
GHWL
t
ELWL
t
WHEH
t
WLWH
t
WHWL
t
WHWH
1
t
WHWH
2
0
0
0
45
20
8
15
50
500
4
500
40
15
50
500
4
500
50
t
OESP
t
RP
t
BUSY
AC Characteristics – Read Only Operations
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Parameter
Read Cycle Time
(1)
Parameter
Symbol
JEDEC
t
AVAV
t
AVQV
t
ELQV
t
GLQV
t
EHQZ
t
GHQZ
t
AXQX
0
90ns
Min
90
90
90
40
20
20
Max
120ns
Min
120
120
120
50
30
0
0
30
Max
150ns
Min
150
150
150
55
35
0
0
35
Max
Units
ns
ns
ns
ns
ns
ns
ns
20
µs
Symbol
Standard
t
RC
t
ACC
t
CE
t
OE
t
DF
t
DF
t
OH
t
READY
Address to Output Delay
CE to Output Delay
OE to Output Delay
CE to Output in High Z
(1)
OE to Output in High Z
(1)
Output Hold from Addresses, CE or OE Change, Whichever Occurs
First
RESET Low to Read Mode
(1)
Notes:
1. Not 100% tested.
20
20
Aeroflex Circuit Technology
4
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
AC Characteristics – Write/Erase/Program Operations – CE Controlled
(T
C
= -55°C to +125°C, V
CC
= +4.5V to + 5.5V, Unless otherwise specified)
Parameter
Parameter
Write Cycle Time
(1)
Parameter
Symbol
JEDEC
t
AVAV
t
AVEL
t
ELAX
t
DVEH
t
EHDX
90ns
Min
90
0
45
45
0
0
0
10
Max
120ns
Min
120
0
50
50
0
0
0
10
0
0
0
50
20
8
Max
150ns
Min
150
0
50
50
0
0
0
10
0
0
0
50
20
8
Max
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
15
Sec
Symbol
Standard
t
WC
t
AS
t
AH
t
DS
t
DH
t
OES
Read
Toggle Bit I and Data Polling
t
OEH
t
GHEL
t
WS
t
WH
t
CP
t
CPH
t
WHWH
1
t
WHWH
2
Address Setup to CE Going Low
Address Hold Time from CE Low
Data Setup to CE Going High
Data Hold Time from CE High
Output Enable Setup Time
(1)
Output Enable Hold Time
(1)
Read Recover Time Before Write
(OE High to WE Low)
CE Setup Time from WE Low
WE Hold Time from CE High
WE Pulse Width
WE Pulse Width High
Byte Programming Operation
Sector Erase Operation
Notes:
1. Not 100% tested.
t
GHEL
t
WLEL
t
EHWH
t
ELEH
t
ELEL
t
WHWH
1
t
WHWH
2
0
0
0
45
20
8
15
15
Aeroflex Circuit Technology
5
SCD1666A REV A 9/12/97 Plainview NY (516) 694-6700
Unit testing refers to basic testing of a piece of code, the actual size of which is undetermined, usually a function or subroutine, and is generally performed by developers. Integration testing, in w...
I selected the option to load the USB drive in the kernel configuration, but it was incorrect. The USB drive was not recognized. Is it because the USB drive driver of my target board is designed for a...
To learn electrical engineering well, you must understand the concepts of some physical quantities in electrical engineering. For this purpose, I will summarize and annotate some commonly used electri...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
People who often surf the Internet until late at night, their families always complain that turning on the big lights in the living room affects their rest, but some people don't have keyboard ligh...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
introduction
Sudan's Muglad Oilfield is a large oilfield jointly invested, developed and constructed by a four-party consortium of China, Malaysia, Canada and Sudan. It consists of 8 satellite...[Details]
1 Introduction
CAN (Controller Area Network) bus is a kind of field bus. It is used in many industrial sectors due to its outstanding advantages such as high performance, high reliability, high...[Details]
The rotor of the brushless DC motor used in electric bicycles is composed of 30 to 40 pieces of NdFeB magnets. Since the surface magnetic field strength of NdFeB magnets exceeds 500mT, the position se...[Details]
Single-chip microcomputer is the abbreviation of single-chip microcomputer. It is made by integrating CPU, ROM, RAM, TIMER/COUNTER and input/output interface (I/O) on a large-scale integrated circu...[Details]
The use of power switches is complex and confusing to most electronic product designers, especially those who are not experts in power management. Power switches are increasingly being used by desi...[Details]
: Ambiguous operators need parenthesesAmbiguous
symbol ``xxx``Argument
list syntax errorArray
bounds
missingArray
size
toolargeBad
character
in paramentersBad
file
name format in i...[Details]
When you are sitting in the subway train, feeling the convenience and comfort brought by the underground rail train, at this time, in the control center, the "brain" of the subway, a group of people a...[Details]
One of the most common requirements of the automotive industry for automotive electronic systems is to achieve the best detection results in the smallest space. This is exactly the advantage of shunt ...[Details]
Two typical electric vehicle flasher circuits are given, and the parameters and specific instructions in the circuit are given. I hope it will be helpful to you!
1. This circuit consists of an...[Details]
Abstract: In a digital signal processing system with DSP as the core, analog-to-digital conversion is an important part of the system. Taking
TMS320C6203B and ADS5422 of
Texas Instruments
...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
