BUW484-0629-22AB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> BUW484-0629-22AB95

BUW484-0629-22AB95: DescriptionIC Socket, BGA484, 484 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

BUW484-0629-22AB95 Overview

IC Socket, BGA484, 484 Contact(s), ROHS COMPLIANT

BUW484-0629-22AB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA484
JESD-609 code	e4/e3
Manufacturer's serial number	BUW
Number of contacts	484
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Fluorescent lamp energy-saving electronic ballast circuit

Radio circuit of monolithic integrated circuit radio

RTS766/RTS767 circuit-a

Mine dust removal delay photoelectric controller circuit

photosensitive oscillator circuit

Illumination automatic control circuit

Summary of commonly used electronic websites: A very good and comprehensive website for microcontrollers, communications, maintenance, electronic design, etc....; 风亦路 Analogue and Mixed Signal

Configuration method of using printf to send data in STM32 serial communication (development environment Keil RVMDK): It is very convenient to use printf to send data in the STM32 serial communication program. However, there are always problems when you first use it. Here are some configurations you need to do to use...; 李威键 ARM Technology

S3C2440 read Nand Flash chip ID problem: The Nand Flash model on the development board is K9F1G08U0B. The chip manual says the read data should be EC F1 00 95 40, but I read EC 40 00 EC 40. My project is at http://cache.ourdev.cn/bbs_upload5...; 白开水 Embedded System

Looking for arm2000 timer capture pulse width program: I need to use timer 0 to continuously sample the high-level width of the PWM wave. How can I capture it and how to handle the capture interrupt?...; qybr0159 ARM Technology

Ultrasonic rangefinder based on R7F0C80212: [i=s] This post was last edited by wenyangzeng on 2014-9-10 14:32 [/i] [align=left][size=4] [font=宋体]Thanks to RENESAS for giving me the EZ-CUBE kit, which gave me the opportunity to get in touch with...; wenyangzeng Renesas Electronics MCUs

What is the use of patents in universities?: When I was a freshman, I got a patent, but now it is still in my dorm room. I feel like it is useless and I don’t know how to promote it. Do you have any good suggestions?...; 零下12度半 Talking about work

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components