BCW676-1530-26AB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> BCW676-1530-26AB95

BCW676-1530-26AB95: DescriptionIC Socket, BGA676, 676 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

BCW676-1530-26AB95 Overview

IC Socket, BGA676, 676 Contact(s), ROHS COMPLIANT

BCW676-1530-26AB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA676
Shell material	CERAMIC
JESD-609 code	e4/e3
Manufacturer's serial number	BCW
Number of contacts	676
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

simple inverter circuit

Noise filter circuit using LM387

Electrical schematic diagram of M7130 horizontal axis giant table surface grinder

Implementing Y-△ step-down starting control circuit using three contactors

Switching Power Supply Charging circuit

Thyristor voltage regulating circuit with output power of 1-4kvA

stm32f10 TIM reset mode + DMA + interrupt: I'm doing Manchester decoding recently, using TIM2-ch2 reset mode + input capture mode to capture the count value between every two rising edges, and transfer it to the specified array using DMA (enco...; Inownl stm32/stm8

Human aging is also a kind of "slow descent and demolition method", right?: Bones are brittle, muscles are atrophied, organs are failing, skin is getting more wrinkled year by year, body is getting shorter year by year, and physical strength is becoming increasingly exhausted...; hk6108 Talking

IO port problem: The company plans to make a universal board, because our product is a control box, which requires more IO ports. The use of IO ports is keyboards, encoders, band switches, etc. The output is to contro...; seven_zs stm32/stm8

【GD32L233C-START Review】MODBUS Test: I was quarantined during the epidemic and had nothing to do, so I tested MODBUS on L233 today.The serial port status flag management of L233 is slightly different from that of other series. For exampl...; aple0807 GD32 MCU

TI Digital Power Control Solutions: [i=s]This post was last edited by dontium on 2015-1-23 11:35[/i] [font=宋体][size=10.5pt]This document is TI Power Management Guide 2, which is a sequel to Power Management Guide 1. It introduces TI dig...; 德州仪器 Analogue and Mixed Signal

Does the PWM pin of the DSP need to be used to reconstruct the signal using the IFFT algorithm?: [i=s] This post was last edited by paulhyde on 2014-9-15 09:13 [/i] I. Task Measure the superposition signal of two sinusoidal signals, where x1 is the main signal, with an amplitude of V (offset to 0...; eyes417 Electronics Design Contest

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components