BPW144-1570-12AA95 datasheet, PDF

Datasheet> All Categories > The connector> socket> BPW144-1570-12AA95

BPW144-1570-12AA95: DescriptionIC Socket, BGA144, 144 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

BPW144-1570-12AA95 Overview

IC Socket, BGA144, 144 Contact(s), ROHS COMPLIANT

BPW144-1570-12AA95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA144
Shell material	PLASTIC
JESD-609 code	e4/e3
Number of contacts	144
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Diode IN148 temperature measurement circuit

One of the relay circuits with single button control on and off

3.9 to 5.5V DC regulated power supply circuit

Infrared remote control generator circuit diagram

800MHz, 30W amplifier circuit

Two-input transistor NOR gate circuit

Cytech SOC training course: [size=4][color=#0000ff]I found a SOC training course of Junlong and shared it with you[/color][/size]...; chenzhufly FPGA/CPLD

The problem of not being able to run the main program: [backcolor=rgb(222, 240, 251)]I use STM32F103C8T6 and development environment KEIL5.[/backcolor] [backcolor=rgb(222, 240, 251)]When I run the program, it jumps directly to this interface. Can an exper...; chenbingjy stm32/stm8

atmel 9200 usb problem: I use 9200 to connect USB, and after enabling pull-up, the computer detects an unknown device. Do I need to remove the pull-up afterwards? I can't capture any data using bushound. I can't even capture...; lei5916418 ARM Technology

STM32 uses TIM1 trigger, why not configure TIM1?: It's still the same old question. The ADC of STM32F429 is very confusing when reading the example program. The ADC is configured as ADC_ExternalTrigConv_T1_CC1. This should be triggered by TIM1. Why i...; dontium stm32/stm8

msp432 ccs Error connecting to the target: (Error -1063 @ 0x0) (Error -260: [i=s]This post was last edited by sunduoze on 2016-3-7 21:08[/i] Help: After reinstalling the system after the Chinese New Year, I came back to school and found that CCS could not burn programs to MSP...; sunduoze Microcontroller MCU

Selection of AC servo motors for CNC machine tool feed systems: Refer to the selection method of AC motors for servo feed systems of Mitsubishi Corporation of Japan, and introduce the whole process of AC servo motor selection and inspection with examples....; frozenviolet Industrial Control Electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components