EEWORLDEEWORLDEEWORLD

Part Number

Search

1200SG1G00JF3RB

Description
Strain Guage Sensor, Gage, -15Psi Min, 85Psi Max, 0.5%, 0-10V, Cylindrical,
CategoryThe sensor    Sensor/transducer   
File Size507KB,4 Pages
ManufacturerGems Sensors & Controls
Download Datasheet Parametric View All

1200SG1G00JF3RB Overview

Strain Guage Sensor, Gage, -15Psi Min, 85Psi Max, 0.5%, 0-10V, Cylindrical,

1200SG1G00JF3RB Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Reach Compliance Codecompli
Maximum accuracy(%)0.5%
shellSTAINLESS STEEL
Nominal offset0V
Maximum operating temperature50 °C
Minimum operating temperature-20 °C
Output range0-10V
Output typeANALOG VOLTAGE
Package Shape/FormCYLINDRICAL
port type1/4 NPT MALE
Maximum pressure range85 Psi
Minimum pressure range-15 Psi
Pressure sensing modeGAGE
Sensor/Transducer TypePRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage35 V
Minimum supply voltage1.5 V
Termination typeCABLE
Base Number Matches1
I wonder which websites you go to for medical information?
Personal recommendation: Medi Medical Information Network. I feel that the content is updated quickly and you can grasp the trends, but many of the articles are only available to corporate members....
老夫子 Medical Electronics
Urgent! Accelerometer to measure car
Now we use ST's LIss33de acceleration sensor to measure the acceleration of the car! But when we measured it on the car, the output data did not change, which made us very depressed! Let's talk about ...
kgsz Sensor
Discussion about timescale in Verilog
There is no default timescale in Verilog . A Verilog module without a specified timescale may mistakenly inherit the invalid timescale parameters of the previously compiled module. Therefore, the Veri...
eeleader FPGA/CPLD
ULN2004AN.pdf
[i=s]This post was last edited by paulhyde on 2014-9-15 09:18[/i]...
cheng_bao1 Electronics Design Contest
[Question] Some programs fail to run after powering on STM32F103RCT6
I used the F103 chip to collect the keyboard SPI interface, and used serial port 1 to assist in printing debugging information. Boot0/1 are both 0 levels, and both start the code from Flash.I found th...
kpbearmo stm32/stm8
What are the problems encountered when using the AT commands of the BenQ M23 GPRS module?
I use the M23 built-in TCP/IP protocol stack to access the target service directly through the following steps: AT+CGDCONT=1,"IP","cmnet" OKAT%CGPCO=1,"PAP,,",1 OKAT$NOSLEEP=1 OKAT$DESTINFO="xxx.xxx.x...
juhao0122 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1676  2041  1989  1388  1621  34  42  41  28  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号