EEWORLDEEWORLDEEWORLD

Part Number

Search

CO-203A19VWL1ATFREQ1

Description
Sine Output Oscillator, 1MHz Min, 4MHz Max
CategoryPassive components    oscillator   
File Size851KB,4 Pages
ManufacturerDover Corporation
Download Datasheet Parametric View All

CO-203A19VWL1ATFREQ1 Overview

Sine Output Oscillator, 1MHz Min, 4MHz Max

CO-203A19VWL1ATFREQ1 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
Other featuresAT CUT CRYSTAL
Ageing1 PPM/YEAR
Maximum control voltage6 V
Minimum control voltage
Frequency Adjustment - MechanicalYES
frequency stability0.001%
Frequency Stability - Voltage0.05 ppm
input power3 W
Installation featuresCHASSIS MOUNT
offset frequency1 kHz
Maximum operating frequency4 MHz
Minimum operating frequency1 MHz
Maximum operating temperature35 °C
Minimum operating temperature15 °C
Oscillator typeSINE
Output impedance50 Ω
Output level2.8284 V
Oven power supply voltage24V
physical size51mm x 51mm x 104mm
Nominal supply voltage24 V
surface mountNO
Base Number Matches1
Integrated circuit detection method
Editor's note: Although there are ways to replace integrated circuits, disassembly is troublesome after all. Therefore, before disassembly, you should accurately determine whether the integrated circu...
fighting Test/Measurement
Could you please tell me about the drift suppression principle of single-output differential amplifier circuit?
If the two output terminals of the differential amplifier circuit are connected to the collectors of two transistors respectively, then they can effectively suppress drift. However, if it is a single ...
enlwm Analog electronics
Looking for msp430&&nRF24L01 battery powered system
I am working on a wireless data download project based on msp430 and nRF24L01 When powered by a power supply, data downloading is normal.But when it comes to battery powered systems, there are problem...
chhd1128 Microcontroller MCU
wince 5.0 power display
There is no power display on my wince 5.0 development board. How can I implement it? It's so troublesome. I checked some information, but I still have no idea. It says that hardware support is needed,...
ntdx Embedded System
Designing CAN rate converter using visual programming
CAN rate conversion is a common application. For example, to connect a 250Kpbs CAN bus to a 500Kbps bus so that the data can be communicated, rate conversion is required. As shown in the following fig...
如越 Automotive Electronics
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2305  2758  631  1624  1977  47  56  13  33  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号