EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342K07B150JRT0V

Description
RESISTOR, THIN FILM, 0.25 W, 5 %, 100 ppm, 150 ohm, SURFACE MOUNT, 1206, CHIP
CategoryPassive components    The resistor   
File Size111KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342K07B150JRT0V Overview

RESISTOR, THIN FILM, 0.25 W, 5 %, 100 ppm, 150 ohm, SURFACE MOUNT, 1206, CHIP

D55342K07B150JRT0V Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
package instructionSMT, 1206
Reach Compliance Codeunknown
Other featuresLASER TRIMMABLE, NON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length3.2 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width1.6 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance150 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceTin/Lead (Sn60Pb40) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance5%
Operating Voltage100 V
Base Number Matches1
E/H (Military M/D55342)
Vishay Thin Film
QPL MIL-PRF-55342 Qualified Thin Film Resistor Chips
FEATURES
Established reliability, “R” failure rate level (100 ppm), C = 2
High purity alumina substrate 99.6 % purity
Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+ 150 °C operating conditions
Very low noise and voltage coefficient
(< - 25 dB, 0.5 ppm/V)
Non-inductive
Laser-trimmed tolerances ± 0.1 %
Wraparound resistance less than 0.010
Ω
typical
In-lot tracking less than 5 ppm/°C
Complete MIL-testing available in-house
Antistatic waffle pack or tape and reel packaging available
Military/aerospace/QPL
SURFACE MOUNT
CHIPS
Actual Size
M55342/02
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing. Wafer is sawed producing exact dimensions and
clean, straight edges.
Note
Specification changed
MIL-PRF-55342
by
DSCC
from
MIL-R-55342
to
CONSTRUCTION
TYPICAL PERFORMANCE
ABS
Passivation
Resistor film
Solder
coating
Nickel barrier
High ourity
alumina substrate
Adhesion layer
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
Test
Material
Absolute TCR
Absolute Tolerance
Stability:
ΔR
Absolute
Voltage Coefficient
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability
SPECIFICATIONS
Passivated nichrome
± 25 ppm/°C to ± 300 ppm/°C TCR
± 0.1 %
± 0.1 %
± 0.5 ppm/V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
- 25 dB
100 ppm
1 year at + 25 °C
- 55 °C to + 125 °C
+ 25 °C
2000 h at + 70 °C
CONDITIONS
www.vishay.com
50
For technical questions, contact:
thin-film@vishay.com
Document Number: 60018
Revision: 16-Sep-09
Analyze the problems that may arise in daily use of infrared cameras
Red burst problem Some manufacturers promote whether they can produce infrared lamps without red burst as a technical issue, as if red burst means low technology and no red burst means high technology...
xyh_521 Industrial Control Electronics
Chapter 3 General GPIO Operation of MSP-EXP430F5529LP
I. Simple operation of general I/O Refer to MSP430X5XX datasheet.pdf 1.1 Introduction to I/O Features: l Multiple multiplexing and settings (i.e., whether to control input, output, whether to connect ...
shmily53 Microcontroller MCU
After FIR filtering, the number of points increases. How to select points to calculate RMS?
Assuming the number of sampling points is 16 and the number of filter coefficients is 17, the number of points after FIR digital filtering should be 16+17-1=32 points. I want to calculate the effectiv...
alice84 Embedded System
C language learning notes
[i=s]This post was last edited by dochance on 2015-3-24 22:04[/i] [size=6]GCC's processing process:[/size] [size=4]1. Preprocessing This stage is used to process all preprocessing instructions. [/size...
dochance Programming Basics
Implementation of soft subtitles in embedded systems (ARGB1555) Application of freetype
[i=s] This post was last edited by 37°Man on 2014-6-26 14:10[/i] [font=Microsoft YaHei][size=4]I haven't written notes for a long time, so I'll organize some information and share it with you[/size][/...
37°男人 DSP and ARM Processors
【R7F0C809】First look at Renesas development kit
It has been a while since I received EZ-CUBE&R7F0C809. Due to my busy work, I have not studied it carefully. This time I received the Renesas development board, which I feel is exquisitely made, worth...
zjbwxl Renesas Electronics MCUs

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2499  1619  2225  1491  925  51  33  45  31  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号