EEWORLDEEWORLDEEWORLD

Part Number

Search

PHAP3305T

Description
KEYPAD SWITCH, SPST, MOMENTARY-TACTILE, 0.05A, 12VDC, 2.1 N, THROUGH HOLE-STRAIGHT
Categoryunclassified   
File Size405KB,14 Pages
ManufacturerETC
Download Datasheet Parametric View All

PHAP3305T Overview

KEYPAD SWITCH, SPST, MOMENTARY-TACTILE, 0.05A, 12VDC, 2.1 N, THROUGH HOLE-STRAIGHT

PHAP3305T Parametric

Parameter NameAttribute value
Maximum DC contact current0.0500 A
Maximum DC contact voltage12 V
Minimum operating temperature-20 Cel
Maximum operating temperature70 Cel
each_compliYes
stateActive
Switch typeKEYPAD SWITCH
ctuator_angle0.0 deg
ctuator_colBLACK
ctuator_length0.0550 inch
ctuator_travel__mm_.254
Control valve typePLUNGER TYPE
width6 mm
high3.6 mm
length or diameter6 mm
Circuit configuration1X1
Maximum contact jitter time10 ms
contact_dc_max_rating_r_load.05A@12VDC
contact_functi(ON)-OFF
contact_resistance0.1000 ohm
dielectric_withstand_volts__v_250VAC
Electrical life100000 Cycle(s)
insulation_resistance1.00E8 ohm
jesd_609_codee4
Manufacturer SeriesPHAP33
Installation featuresTHROUGH HOLE-STRAIGHT
Number of switches1
maximum control2.1 N
cking_methodBAG
solderabilityWAVE
Switch actionMOMENTARY-TACTILE
switch functionSPST
terminal coatingSILVER
erminal_length0.1370 inch
Terminal typeSOLDER
PHAP33 series
Tact switches
Distinctive features and specifications
Wide range of case formats
SMT and through-hole models
Normally closed models available
Models
Performances
Current/voltage rating
Contact resistance
Insulation resistance
Dielectric strength
Electrical life (cycles)
Operating force
Travel
Operating temperature
Storage temperature
Vibrations
IR reflow soldering
Wave soldering
Manual soldering
PHAP3381
PHAP3382
PHAP3383
PHAP3384
PHAP3390
PHAP3391
PHAP3371
PHAP3372
PHAP3373
PHAP3374
PHAP3378
PHAP3355
PHAP3361
PHAP3362
PHAP3363
PHAP3365
PHAP3366
PHAP3301
PHAP3302
PHAP3303
PHAP3305
PHAP3306
PHAP3307
PHAP3308
PHAP3368
PHAP3350
PHAP3351
PHAP3352
PHAP3353
PHAP3320
PHAP3321
C
50mA 12VDC
100 mΩ max.
100 MΩ min.
250 VAC min. (1 minute)
70.000
1,6N
± 0,5N
0,20/ 0,25 mm
75.000
1,6N
+0,5/-0,3N
0,25 mm
30.000
1,8N
± 0,5N
0,25 mm
100.000
1,6N
± 0,5N
0,25 mm
100.000
2N
± 0,3N
0,50 mm
100.000
1,6N
± 0,5N
0,30 mm
-20°C to +70°C
-30°C to +80°C
10-500 Hz / 10 g
240°C for 20 seconds max.
255°C for 5 seconds max.
300°C for 3 seconds max.
-
Dimensions
: First dimensions are in mm while inches are shown as bracketted numbers.
Packaging unit
: 1.000 pieces and multiples, except for tape and reel packaging (see following pages).
APEM
www.apem.com
C-3
What is the operating temperature range of STM8?
TO Moderator:What is the ambient temperature in which STM8 can work?I have measured the highest temperature, which can reach 150 degrees, and some are 130 degrees....
zrb3338044 stm32/stm8
Industry Forum 2 Tan Jun: Exploring the Winning Way of Consumer Electronics Speech Download (Part 1)
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:02[/i] Mr. Tan Jun, President of ARM China, has delved into the "Apple Core" and stood on the "Industry Ball", using two new perspectiv...
呱呱 Mobile and portable
Platform: 2440, bootloader problem
My bsp contains stepldr and eboot. I want to run eboot. However, after burning stepldr.nb1 into flash, dnw displays garbled characters! ! ! ! This is the initial code of the serial port: void Uart_Ini...
linlinne Embedded System
Problems with the STM32F746NGH6 board
I just came into contact with the F7 board recently. I transplanted the program on the previous STM32F407 board to the F746, and found that the running speed of the F746 is not as fast as that of the ...
滴水 stm32/stm8
[ATMEL SAM R21] Preliminary analysis of WsnDemo communication process
I have studied the communication process of WsnDemo in ASF these days, and I will give you a brief analysis for your reference. First, let's look at the main program file main.c. The main program of W...
dcexpert Microchip MCU
About global variables
Sometimes you have to use global variables, for example, to communicate with an interrupt service routine. Instead of writing like this: int timer = 0; it is better to write like this: inline int* Tim...
成风 Programming Basics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1753  227  1408  1364  2900  36  5  29  28  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号