EEWORLDEEWORLDEEWORLD

Part Number

Search

3GDF8-F-80T-38.000

Description
LVDS Output Clock Oscillator, 38MHz Nom, DIP-8/4
CategoryPassive components    oscillator   
File Size109KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Download Datasheet Parametric View All

3GDF8-F-80T-38.000 Overview

LVDS Output Clock Oscillator, 38MHz Nom, DIP-8/4

3GDF8-F-80T-38.000 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
MakerEuroquartz
Reach Compliance Codecompliant
Maximum control voltage3 V
Minimum control voltage0.3 V
maximum descent time0.7 ns
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
frequency stability100%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency38 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeLVDS
Output load50 OHM
physical size12.8mm x 12.8mm x 5.08mm
longest rise time0.7 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
8 pin Dual-in-Line
Frequency range 38MHz to 640MHz
LVDS Output
Supply Voltage 3.3 VDC
Phase jitter 0.4ps typical
Pull range from ±30ppm to ±150ppm
GDF8 LVDS VCXO
38.0MHz to 640.0MHz
DESCRIPTION
GDF8 VCXOs are packaged in an industry-standard 8 pin dual-in-line
package. Typical phase jitter for GDF series VCXOs is 0.4 ps. Output
is LVDS. Applications include phase lock loop, SONET/ATM, set-top
boxes, MPEG , audio/video modulation, video game consoles and
HDTV.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
RMS Period Jitter:
Peak to Peak Jitter:
Phase Jitter:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Control Voltage Range:
Temperature Stability:
Output Load:
Rise/Fall Times:
Duty Cycle:
Start-up Time:
Current Consumption:
Static Discharge Protection:
Storage Temperature:
Ageing:
Enable/Disable:
RoHS Status:
OUTLINE & DIMENSIONS
38.0MHz to 640.0MHz
3.3 VDC ±5%
LVDS
3.0ps typical
20.0ps typical, 30.0ps maximum
0.4ps typical, 5.0ps maximum
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
1.4 Volts typical
1.1 Volts typical
From ±30ppm to ±150ppm
1.65 ±1.35 Volts
See table
50W into Vdd or Thevenin equiv.
0.5ns typ., 0.7ns max.
20% Vdd to 80% Vdd
50% ±5%
(Measured at Vdd-1.3V)
10ms maximum, 5ms typical
55mA typical, 60mA maximum
(At 202.50MHz)
2kV maximum
-55° to +150°C
±2ppm per year maximum
Not implemented - 4 pin package
Fully compliant or non compliant
PART NUMBERING
Example:
Supply Voltage
3 = +3.3V
Series Designator
GDF8
RoHS Status
G = RoHs compliant
Blank = RoHS non-compliant
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
3GPF8G-B-80N-60.000
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
About RF module shielding
[table=95%][tr][td]I made a module, CC1000 plus a PA (MAX2232), the power is about 100mW, I don't know if I need to add a shield? Please give me some advice. [/td][/tr][/table]...
yihui0323 RF/Wirelessly
recruitment
1. Linux development engineer withmore than three years of development and debugging experience, familiar with Intel and ARM platforms, and able to develop board-level BSP is preferred 2. FPGA develop...
诺小诺 Recruitment
Help
Is it true that gain error in ADC12 will only cause accuracy loss but not code loss? If so, could you explain?...
zzbaizhi Microcontroller MCU
LPC114 Application
Very curious! :Q :Q...
xianglin134 NXP MCU
Please tell me what type of microcontroller is this?
Forum masters, I want to learn about microcontrollers. There is a circuit where the microcontroller has erased words (the package is LQFP64). I have searched for a long time but still can't find any r...
本杰明 MCU
I burned the program into the 51 development board, but the numbers displayed on the digital tube kept flashing. Can anyone tell me where the problem is?
#include #include #include "XPT2046.h" //--Define the IO used--// #define GPIO_DIG P0 //Digital tube IO port sbit LSA = P2^2; sbit LSB = P2^3; sbit LSC = P2^4; #define GPIO_KEY P1 //Independent keyboa...
真龙破天 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2250  1413  1222  1315  2142  46  29  25  27  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号