EEWORLDEEWORLDEEWORLD

Part Number

Search

3GDF8G-B-150M-640.000

Description
LVDS Output Clock Oscillator, 640MHz Nom, ROHS COMPLIANT, DIP-8/4
CategoryPassive components    oscillator   
File Size109KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

3GDF8G-B-150M-640.000 Overview

LVDS Output Clock Oscillator, 640MHz Nom, ROHS COMPLIANT, DIP-8/4

3GDF8G-B-150M-640.000 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerEuroquartz
Reach Compliance Codecompliant
Maximum control voltage3 V
Minimum control voltage0.3 V
maximum descent time0.7 ns
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate150 ppm
frequency stability50%
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency640 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVDS
Output load50 OHM
physical size12.8mm x 12.8mm x 5.08mm
longest rise time0.7 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountNO
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
8 pin Dual-in-Line
Frequency range 38MHz to 640MHz
LVDS Output
Supply Voltage 3.3 VDC
Phase jitter 0.4ps typical
Pull range from ±30ppm to ±150ppm
GDF8 LVDS VCXO
38.0MHz to 640.0MHz
DESCRIPTION
GDF8 VCXOs are packaged in an industry-standard 8 pin dual-in-line
package. Typical phase jitter for GDF series VCXOs is 0.4 ps. Output
is LVDS. Applications include phase lock loop, SONET/ATM, set-top
boxes, MPEG , audio/video modulation, video game consoles and
HDTV.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
RMS Period Jitter:
Peak to Peak Jitter:
Phase Jitter:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Control Voltage Range:
Temperature Stability:
Output Load:
Rise/Fall Times:
Duty Cycle:
Start-up Time:
Current Consumption:
Static Discharge Protection:
Storage Temperature:
Ageing:
Enable/Disable:
RoHS Status:
OUTLINE & DIMENSIONS
38.0MHz to 640.0MHz
3.3 VDC ±5%
LVDS
3.0ps typical
20.0ps typical, 30.0ps maximum
0.4ps typical, 5.0ps maximum
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
1.4 Volts typical
1.1 Volts typical
From ±30ppm to ±150ppm
1.65 ±1.35 Volts
See table
50W into Vdd or Thevenin equiv.
0.5ns typ., 0.7ns max.
20% Vdd to 80% Vdd
50% ±5%
(Measured at Vdd-1.3V)
10ms maximum, 5ms typical
55mA typical, 60mA maximum
(At 202.50MHz)
2kV maximum
-55° to +150°C
±2ppm per year maximum
Not implemented - 4 pin package
Fully compliant or non compliant
PART NUMBERING
Example:
Supply Voltage
3 = +3.3V
Series Designator
GDF8
RoHS Status
G = RoHs compliant
Blank = RoHS non-compliant
Stability over temperature range
(See table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
3GPF8G-B-80N-60.000
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
About ADXL203 to measure tilt angle
When using ADXL203 to measure the tilt angle, the output should be 2.5V at 0° and 3.5V at 90°. The outputs I measured in the experiment were 2.5038V and 3.509V, which are basically correct. However, s...
lene ADI Reference Circuit
Use jlink to download the program to stm32, the jlink red light flashes, and finally the microcontroller cannot be recognized
When using jlink's sw mode to download the program, the debug window cannot recognize the MCU. jlink can be downloaded normally on other boards, so there is no problem with jlink, and there is no prob...
研究深 stm32/stm8
How can I create a WINCE emulator running on a PC with an ARMV4I CPU?
How can I use PB to create a WINCE simulator with ARMV4I CPU running on PC? Just explain the key steps. It seems that I cannot select two CPUs. If I select X86 and ARMV4I, there is no corresponding si...
bbs_cq Embedded System
My wireless network is not working, the driver is fine, it was working yesterday but not today
My laptop is ASUS x50sl. It was working fine yesterday, but not today. I installed the system and drivers, but still can't get on, and reports this error: Name: Association test Description: This test...
6562748 Embedded System
Request Wince system customization information
Who has more detailed information about Wince system customization? Can you send me a copy? My email: baiminshengbai@126.com Send me a message and I will give you a copy. Thank you...
heater Embedded System
How to implement a power switch similar to a mobile phone
From EEWORLD cooperation group: arm linux fpga embedded 0 (49900581) That is: long press the button to turn it on and off. Now it is realized by adding a trigger and a power IC, but the effect is not ...
小天 Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1540  279  2413  2579  2098  32  6  49  52  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号