Preparation before layout: 1 Check whether the snap point is set correctly. The snap point is 0.1 for 08 process, 0.05 for 06 process, and 0.025 for 05 process. 2 The cell name cannot start with a num...
1. After completing the basic framework design, gradually increase the system to increase the call of system resources, this time increase SPI.
2. SPI requires 4 pins, SPI0 is used here, which occupie...
I want to learn how to write some algorithms in Verilog, but I don't know where to start. Can an expert help me write a 4-point or 1-point FFT program in Verilog? Thanks!...
Activity introduction: As the creator of the global RISC standard, ARM's dominant position in the field of embedded processors has long been recognized by everyone. Currently, more than 90% of embedde...
PADS schematic and circuit board design full process video (8 hours)-06 PADS is the most commonly used circuit board design software in China, and is favored by the majority of electronic hardware des...
In recent years, as energy consumption and environmental protection issues have attracted people's attention, my country's solar photovoltaic power generation industry has shown a rapid development...[Details]
Recently, the results of the 2018 German Red Dot Design Award were announced. GoodWe, a company located in Suzhou High-tech Zone, stood out among thousands of outstanding design products from 5...[Details]
In the war without gunpowder between China and the United States,
ZTE
has become a new victim. The seven-year chip ban by the United States has pushed this communications giant to a life-or...[Details]
1. Purpose In actual product release, if the program stored in the MCU Flash is not protected, some illegal companies may read the program in the Flash through an emulator (J-Link, ST-Link, e...[Details]
1. Purpose Since the number of times the STM32 FLASH can be erased and written is limited, in order to protect our FLASH and extend the use time of the MCU, we can debug on the SRAM. SRAM is a ...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
Because the STM32 HAL library only has millisecond-level delay for HAl_Delay(), in order to achieve accurate microsecond-level delay, Systick has to be modified. However, since it is used internally ...[Details]
From last year to now, competition in the photovoltaic inverter industry has become increasingly fierce. In addition to the introduction of new products, various marketing and promotion methods hav...[Details]
Recently, the "Smart Photovoltaic Industry Development Action Plan (2018-2020)" jointly issued by six departments has put this concept on the forefront. Photovoltaic smart solutions will become the ne...[Details]
China Energy Storage Network News:
The State Grid Corporation of China, this elephant, is planning to turn around and enter the emerging power service market.
The rallying cry for the tr...[Details]
According to foreign media reports, the 2018 GMC Terrain Denali is equipped with multiple collision detection systems, and a recent test verified the safety of the system. Even when driving in a bu...[Details]
In the Huaxing Optoelectronics LCD panel
factory
located in Guangming New District, Shenzhen
, apart from a few people repairing machines, it is often difficult to see other people. Here, ev...[Details]
At the just concluded InfoComm 2018 exhibition, the two major brands, Zhongke Jiguang and China Hualu, both displayed three-color light source
laser TVs
. The outstanding color performance ...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
