AC-DC
120-180 Watts
SDS Series
•
•
•
•
•
•
•
Convection-cooled
3”x 5”Footprint
Up to 90% Efficiency
xppower.com
Open Frame, U-Channel & Covered Versions
Low Temperature Option
Single & Multi Outputs
3 Year Warranty
Specification
Input
• 90-264 VAC (120-370 VDC)
• 47-63 Hz
• 120 W: 1.7 / 1.0 A max at 115 / 230 VAC
150 W: 2.0 / 0.8 A max at 115 / 230 VAC
180 W: 2.7 A max at 90 VAC
• 120 W: 20 / 51 A max at 115 / 230 VAC
Inrush Current
150 W: 54 / 63 A max at 115 / 230 VAC
180 W: 54 / 108 A max at 115 / 230 VAC
Power Factor
• >0.9
Earth Leakage Current
• 120 W: 0.30 / 0.75 mA at 115 / 230 VAC
150 W: 0.40 / 0.75 mA at 115 / 230 VAC
180 W: 0.75 mA at 230 VAC
Input Protection
• Internal T3.15 A / 250 VAC fuse in line
No Load Input Power
• 180 W:
<0.5
W
Input Voltage
Input Frequency
Input Current
General
Efficiency
Isolation
Isolation Resistance
Switching Frequency
• 120 W: 80% typical
150 W and 180 W: 88% typical
• 3000 VAC Input to Output, 1500 VAC Input
to Ground, 500 VDC Output to Ground
• 50 MΩ
• 120 W: PFC 100 kHz typical, PWM 67 kHz
typical. 150 W: PFC 34 kHz minimum,
PWM 55 kHz typical. 180 W: PFC 67 kHz
typical, PWM 67 kHz typical
• 120 W: 4.87 W/In
3
, 150 W: 6.50 W/In
3
180 W: 7.47 W/In
3
• Power Fail Detect = TTL active low,
combined AC and DC OK signal
(-P versions SDS120 & 150 only)
Warning time 16 ms
• >130 kHrs to MIL-HDBK-217F at 25 °C, GB
Power Density
Signals
Output
• See table
• ±5% output 1 only (3.3 V variant ±10%)
SDS180: not user adjustable
Initial Set Accuracy
• Single output models: ±1%
Multi-output models: ±5%
Minimum Load
• No minimum load required for single
output models. For multi-output models
(see table)
Start Up Delay
• 2 s max
• 2 ms typical
Start Up Rise Time
Hold Up Time
• 16 ms minimum at full load and 110 VAC
Line Regulation
• 0.5% typical
Load Regulation
• 3.0% typical
Transient Response
• 4% max deviation, recovery to within
1% in 500 µs for a 50% load change
Ripple & Noise
• 1% pk-pk typical, 20 MHz bandwidth
Overvoltage Protection
• 112-132% V1 only, recycle input to reset
Overload Protection
• All outputs: 110-150% with auto recovery
(primary power limit)
Short Circuit Protection
• Trip & restart (hiccup mode),
auto recovery
Temperature
• ±0.04%/°C
Coefficient
Output Voltage
Output Voltage Trim
MTBF
Environmental
Operating Temperature
• 0 °C to +70 °C (-20 °C to +70 °C, SDS180),
derate linearly from 100% load at +50 °C
to 50% load at +70 °C,
for low temperature option add suffix -L:
-40 °C to +70 °C, SDS120 and SDS150,
not available for SDS180
Cooling
• Convection-cooled
Operating Humidity
• 5-95% RH, non-condensing
Storage Temperature
• -40 °C to +85 °C
EMC & Safety
Emissions
Harmonic Currents
Voltage Flicker
ESD Immunity
Radiated Immunity
EFT/Burst
Surge
Conducted Immunity
Magnetic Field
Dips & Interruptions
Safety Approvals
•
•
•
•
•
•
•
•
•
•
•
EN55022, level B conducted & radiated.
EN61000-3-2 class A
EN61000-3-3
EN61000-4-2, level 2 contact, Perf Criteria A
SDS150: level 3 air, Perf criteria A
EN61000-4-3, level 2, Perf Criteria A
EN61000-4-4, level 2, Perf Criteria A
EN61000-4-5, installation class 3,
Perf Criteria A
EN61000-4-6, level 2 , Perf Criteria A
EN61000-4-8, 1 A/m, Perf Criteria A
EN61000-4-11, 30% 10 ms, 60% 100 ms,
>95% 5000 ms Perf Criteria A, B, B
EN60950-1, UL60950-1,CSA60950-1
per cUL.
AC-DC
Models and Ratings
Output
Power
72.0 W
110.0 W
115.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
79.5 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
91.5 W
91.5 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
120.0 W
Vnom
3.3 V
5.0 V
7.0 V
9.0 V
12.0 V
15.0 V
18.0 V
24.0 V
28.0 V
36.0 V
48.0 V
+3.3 V
+3.3 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+28.0 V
+3.3 V
+3.3 V
+3.3 V
+3.3 V
+3.3 V
+3.3 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
+5.0 V
Output 1
Imin
Imax
0.00 A
22.00 A
0.00 A
22.00 A
0.00 A
16.42 A
0.00 A
13.33 A
0.00 A
10.00 A
0.00 A
8.00 A
0.00 A
6.66 A
0.00 A
5.00 A
0.00 A
4.28 A
0.00 A
3.33 A
0.00 A
2.50 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
0.39 A
3.92 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
1.50 A
15.00 A
Tol.
(1)
5%
5%
5%
4%
3%
3%
3%
2%
2%
2%
2%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Vnom
Output 2
Imin
Imax
Tol.
(1)
Vnom
Output 3
Imin
Imax
SDS120
Tol.
(1)
Model Number
(2, 4, 5)
SDS120PS03B
SDS120PS05B
SDS120PS07B
SDS120PS09B
SDS120PS12B
SDS120PS15B
SDS120PS18B
SDS120PS24B
SDS120PS28B
SDS120PS36B
SDS120PS48B
SDS120PD00B
SDS120PD01B
SDS120PD02B
SDS120PD03B
SDS120PD04B
SDS120PD05B
SDS120PD06B
SDS120PT00B
SDS120PT01B
SDS120PT02B
SDS120PT03B
SDS120PT04B
SDS120PT05B
SDS120PT06B
SDS120PT07B
SDS120PT08B
SDS120PT09B
SDS120PT10B
SDS120PT11B
SDS120PT12B
SDS120PT13B
SDS120PT14B
SDS120PT15B
SDS120PT16B
SDS120PT17B
+5.0 V
+12.0 V
+12.0 V
+15.0 V
+24.0 V
-24.0 V
+5.0 V
+5.0 V
+5.0 V
+12.0 V
+12.0 V
+12.0 V
+12.0 V
+12.0 V
+12.0 V
+12.0 V
+12.0 V
+15.0 V
+15.0 V
+24.0 V
+24.0 V
+24.0 V
+24.0 V
+10.0 V
+10.0 V
0.40 A
0.20 A
0.20 A
0.20 A
0.10 A
0.20 A
0.20 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.60 A
0.35 A
0.35 A
0.35 A
0.35 A
0.60 A
0.60 A
6.0
6.0
6.0
6.0
3.5
2.0
2.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
6.0
3.5
3.5
3.5
3.5
6.0
6.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
+12.0 V
-12.0 V
+5.0 V
-5.0 V
-12.0 V
+12.0 V
+5.0 V
-5.0 V
-12.0 V
+12.0 V
-15.0 V
+15.0 V
-24.0 V
+24.0 V
-12.0 V
+12.0 V
-10.0 V
+10.0 V
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
1.0
1.0
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.0
1.0
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
Notes
1. Tol. (total regulation) includes line regulation and load regulation.
2. For optional PCB only version, delete suffix ‘B’ from model number.
Example SDS120PS03.
3. For non-standard voltages contact sales.
4. For optional low temperature -40 °C operation, add suffix ‘-L’ to model
number. Example: SDS120PS12B-L
5. For optional Power Fail Detect circuit, add suffix ‘-P’ to model number,
example: SDS120PS12B-P
Mechanical Details
B
B
1.57 (40.0)
4.49 (114.3)
5.00 (127.0)
4.55 (115.6)
C0.3
0.02
(0.60)
0.02
(0.60)
M3xP0.5
ø0.21
(ø5.40)
ø0.25
(ø6.40)
0.09
(2.45)
A
3.01
(76.6)
H1
D0.2
2.57
(65.3)
A
B
B
2.7 (68.58)
3.9 (99.06)
0.01
(0.38)
See section-C (4x)
G1
4.49 (114.25)
4.00 (101.6)
1.21
(30.75)
B
B
B
1.30
(33.2)
B
A
M3xP0.5
section-A (scale 4/1)
0.55 0.09 H3
(13.9) (2.5)
Internal
1.18
1.30
(30.0)
(33.2)
0.79 (20.3)
0.25 (6.4)
1.5 (39.2)
0.22 (5.7)
0.22 (5.6)
ø0
.21
( 5.
4)
0.21
(5.5)
0.25
(6.35)
0.22
(5.6)
+5 V
Power Fail Detect (PFD)
is +5 V for normal opera-
tion.
Pin 13
A
B
B
B
See section-A (4x)
See section-B (11x)
G1
3.21
(81.6)
H2
0.03 0.01
(0.8) (0.3)
Source current is 5 mA
max.
PFD is <0.4 V for either
AC Fail (<90 VAC) or
DC Fail (<95% Vnom).
Sink current is 10 mA max.
See section-B (scale 4/1)
ø0.29
(ø7.44)
0.25 (6.35)
0.79 (20.3)
ø0.14 (ø3.6)
See section-C (scale 4/1)
G2
R2.0
0.85
(21.6)
Notes
0.9
(23.0)
0.15 (4.0)
0.15 (4.0)
1.18 (30.02)
PIN CONNECTIONS
Pin Single
Dual
Triple
Pin
Single
1
V1
V2
V2
8
Return
2
V1
V2
V2
9
Return
3
V1
V1
V1
10
Return
4
V1
V1
V1
11
Return
5
V1
V1
V1
12
Return
6
V1
V1
V1
13
PFD
(1)
7 Return Common Common
Dual
Triple
Common Common
Common Common
N/C
V3
Common Common
Common Common
PFD
(1)
PFD
(1)
1. Optional Power Fail Detect signal on ‘-P’ versions only. Standard models pin 13 is N/C.
2. I/P connector P1 mates with Molex housing 09-50-3051 & Molex 2878 series crimp termi-
nal.
3. O/P P2 mates with Molex housing 09-50-3131 & Molex 2878 series crimp terminal.
4. For optional cover kit order part number SDS120 COVER, to receive unit with cover fitted
add suffix ‘-C’ to model number, e.g. SDS120PS12B-C (overall height is 1.73 (44.0)).
5. For mating connector kit order part number SDS120/SDS150 CON KIT.
6. For cable harness order part number SDS120S LOOM for single output models & SDS120M
LOOM for multi-output models.
7. Maximum mounting screw penetration: 0.14 (3.5)
8. All dimensions are in inches (mm).
9. Weight: 0.77-0.99 lbs (350-450 g) approx.
10. For PCB-only version, overall dimensions are max 5.00 x 3.00 x 1.44 (127.0 x 76.2 x 36.6).
AC-DC
Models and Ratings
Output Power
144 W
150 W
150 W
150 W
150 W
150 W
150 W
150 W
Output Voltage
9V
12 V
15 V
18 V
24 V
30 V
36 V
48 V
Output Current
Minimum
0A
0A
0A
0A
0A
0A
0A
0A
Maximum
16.00 A
12.50 A
10.00 A
8.33 A
6.25 A
5.00 A
4.17 A
3.13 A
Total Regulation
(1)
5%
5%
5%
4%
3%
2%
2%
2%
SDS150
Model Number
(2,4,5,6)
SDS150PS09B
SDS150PS12B
SDS150PS15B
SDS150PS18B
SDS150PS24B
SDS150PS30B
SDS150PS36B
SDS150PS48B
Notes
1. Total regulation includes line regulation and load regulation.
2. For optional 2 pin Molex input, add suffix ‘-D’ to model number. Example SDS150PS12B-D.
3. For non-standard voltages contact sales.
4. For optional low temperature -40 °C operation, add suffix ‘-L’ to model number. Example: SDS150PS12B-L
5. For optional PCB only version, delete suffix ‘B’ from model number. Example SDS150PS48.
6. For optional Power Fail Detect signal (PFD), add suffix ‘-P’ to model number. Example: SDS150PS48B-P.
Mechanical Details
U Channel
0.30 (7.7)
1.18 (30.0)
0.54 (13.6)
G N
P1
M3* P0.5 (Mounting Holes) x 5
AC Input
L
1.18 (30.0)
5.00
(127.0)
4.00 (101.6)
4.50 (114.3)
3.90
(99.0)
4.50
(114.3)
0.25 (6.4)
Pin
1
2
3
4
5
6
0.25
(6.4)
13
2.57 (65.3)
0.55
(14.0)
M3* P0.5 (Mounting Holes) x 4
Pitch = 3.96 mm
DC Output
1 P2
P2 - PIN CONNECTIONS
Function
Pin
V1
7
V1
8
V1
9
V1
10
V1
11
V1
12
13
Function
Return
Return
Return
Return
Return
Return
PFD
(4)
0.67
(16.9)
1.62 (41.2)
Notes
1. All dimensions in inches (mm), tolerance ±0.02 (±0.5).
2. Input connector P1 mates with Molex housing 09-50-3051 and
Molex 2478 series crimp terminal.
3. Output connector P2 mates with Molex housing 09-50-3131 and
Molex 2478 series crimp terminal.
4. Optional power fail detect signal on ‘-P’ versions only. Standard
models pin 13 is not connected.
5. For mating connector kit order part number
SDS120/SDS150 CON KIT.
6. For cable harness order part number SDS150 LOOM.
7. Maximum mounting screw penetration: 0.14 (3.5)
8. For optional cover kit order part number SDS150 COVER
9. Weight: U Channel - 1.27 lbs (580 g) approx.
Open Frame - 0.86 lbs (390 g) approx.
Voltage
Adj.
3.21 (81.5)
Open Frame
1.16 (29.6)
M3 x P0.5 (Mounting Holes) x 4
ø4.0 (Mounting Holes) x 4
1.57 (40.0)
0.80 (20.3)
4.55 (115.6)
Voltage Adj.
P2
1
0.22 (5.7)
0.56 (14.2)
0.22 (5.5)
5.00 (127.0)
+5 V
1.40 (35.6)
Power Fail Detect (PFD)
is +5 V for normal operation.
Pin 13
Source current is 5 mA max.
PFD is <0.4 V for either
AC Fail (<90 VAC) or
DC Fail (<95% Vnom).
Sink current is 10 mA max.
2.57 (65.3)
3.00 (76.2)
AC
Input
DC
Output
L
N
G
P1
13
Pitch = 3.96 mm
3.00 (76.2)
0.32 (7.9)
Internal
0.12 (3.0)
0.43 (10.9)
1.21 (30.7)
0.80 (20.3)
1.16 (29.6)
Models and Ratings
Output Power
170 W
(1)
180 W
180 W
Output Voltage
12 V
24 V
48 V
Output Current
Minimum
0A
0A
0A
Maximum
14.16 A
7.50 A
3.75 A
Total Regulation
(2)
5%
3%
2%
SDS180
Model Number
(3)
SDS180PS12B
SDS180PS24B
SDS180PS48B
AC-DC
Notes
1. Output power is 170 W at highline input and 160 W at low line input, (90-132 VAC).
2. Total regulation includes line regulation and load regulation.
3. For optional L-bracket version, delete suffix ‘B’ from model number. Example SDS180PS48.
4. For non-standard voltages contact sales.
Mechanical Details
U Channel
For 12 V Version Only
25.6 +0.5
Pitch=7.62 mm
DC
Output
4
3.21 (81.6)
0.55
(14.0)
2.57 (65.3)
0.30
(7.7)
1.10
(28.0)
0.25
(6.4)
0.85
(21.6)
LED
Pitch=3.96mm
P2
8
0.25
(6.4)
1.10 (28.0)
1
4.50 (114.3)
5.00
(127.0)
3.90
(99.1)
4.00
(101.6)
4.50
(114.3)
P1
L
N
Pin
1
2
3
4
P2 - PIN CONNECTIONS
24/48 V versions
Function
Pin
Function
Return
5
V1
Return
6
V1
Return
7
V1
Return
8
V1
PIN CONNECTIONS
12 V version
Function
Pin
Function
Return
3
V1
Return
4
V1
M3 x P0.5 (Mounting Holes) x 4
1.54 (39.2)
2.18 (55.4)
M3 x P0.5
(Mounting Holes) x 2
AC Input
M3 x P0.5
(Mounting Holes) x 3
Pin
1
2
For 12 V Version Only
25.6 +0.5
Pitch=7.62 mm
Notes
1. All dimensions in inches (mm),
tolerance ±0.02 (±0.5).
2. Input connector P1 mates with Molex
housing 09-50-3031 and Molex 2478 series
crimp terminal.
3. Output connector P2 mates with Molex housing
09-50-3061 (or 09-50-3081) and Molex 2478
series crimp terminal for 24/48 V Versions. For 12
V Version, output
terminal is screw terminal.
4. For mating connector kit order part
number: SDS180 CON KIT.
5. For cable harness order part number
SDS180 LOOM.
6. Maximum mounting screw penetration: 0.14 (3.5)
7. Weight: U Channel - 1.14 lbs (520 g)
L-bracket - 1.06 lbs (480 g)
L-bracket
0.55
(14.0)
3.13 (79.6)
2.57 (65.3)
0.30
(7.7)
1.10
(28.0)
0.25
(6.4)
DC
Output
4
0.85
(21.6)
1
LED
Pitch=3.96mm
P2
8
5.00
(127.0)
3.90
(99.1)
4.50
(114.3)
P1
L
N
M3 x P0.5 (Mounting Holes) x 4
1.54 (39.2)
2.18 (55.4)
M3 x P0.5
(Mounting Holes) x 2
AC Input
14 May 18
京公网安备 11010802033920号
EEWORLD
