EEWORLDEEWORLDEEWORLD

Part Number

Search

GLDB03A4J-5Q31

Description
Snap Acting/Limit Switch, SPDT, Momentary, 0.55A, 125VDC, Connector Terminal, Lever Actuator, Panel Mount
CategoryMechanical and electronic products    switch   
File Size141KB,1 Pages
ManufacturerHoneywell
Websitehttp://www.ssec.honeywell.com/
Download Datasheet Parametric View All

GLDB03A4J-5Q31 Overview

Snap Acting/Limit Switch, SPDT, Momentary, 0.55A, 125VDC, Connector Terminal, Lever Actuator, Panel Mount

GLDB03A4J-5Q31 Parametric

Parameter NameAttribute value
MakerHoneywell
Reach Compliance Codeunknown
ECCN codeEAR99
Actuator typeLEVER
body width30 mm
body height58.5 mm
Body length or diameter30.5 mm
Contact (AC) maximum rated R load6A@120VAC
Maximum contact current (AC)6 A
Maximum contact current (DC)0.55 A
Contact (DC) maximum rated R load.55A@125VDC
Maximum contact voltage (AC)120 V
Maximum contact voltage (DC)125 V
Manufacturer's serial numberGLD
Installation featuresPANEL MOUNT
Maximum operating force110 N
Maximum operating temperature85 °C
Minimum operating temperature-25 °C
sealIP66
surface mountNO
Switch actionMOMENTARY
switch functionSPDT
Switch typeSNAP ACTING/LIMIT SWITCH
Termination typeCONNECTOR
Recommended FPGA Learning Resources (XVI) - Digital Logic Principles and FPGA Design
, FPGA has experienced a transformation from a supporting role to a leading role since its birth. FPGA is mainly used to replace complex logic circuits. left][color=#565656][backcolor=rgb(237, 235, 23...
tiankai001 Download Centre
IO port write data failed
First, there are four registers, namely GPJCON, GPJDAT, GPJUDP and GPJSEL. GPJCON is set to 0x28555555, and each two bits represent the status of an IO port, 00: input, 01: output, 10: function pin, 1...
heljean Embedded System
Several circuits used by telephone for remote monitoring
Several circuits used by telephone for remote monitoring...
zzzzer16 Industrial Control Electronics
Please give me some advice, it is best to use a single chip microcomputer
[i=s]This post was last edited by paulhyde on 2014-9-15 03:19[/i] 1. Task Design a signal generator that can output a specified waveform in a loop. In addition to sine waves, triangle waves and square...
蓝小亨 Electronics Design Contest
Allegro reports an error when drilling files
When Allegro outputs drilling files, it always reports the error "the number of integer places specified for drill output data is not enough for this design". How to solve it?...
elivis PCB Design
MAC issues with TI M4 chips
What do 10/100 MAC+PHY and 10/100 MAC with MII I/F mean? Looking at TI's M4 selection manual, some have one of them, and some have both. What is the difference between them? I can't find any related q...
awarenessxie Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1375  359  550  76  2278  28  8  12  2  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号