EEWORLDEEWORLDEEWORLD

Part Number

Search

KL44-1R4AXABA222NXX

Description
Rocker Switch, DP3T, Latched And Momentary, 5A, 24VDC, Solder/quick Connect Terminal, Rocker Actuator, Panel Mount
CategoryMechanical and electronic products    switch   
File Size452KB,9 Pages
ManufacturerAPEM
Environmental Compliance
Download Datasheet Parametric View All

KL44-1R4AXABA222NXX Overview

Rocker Switch, DP3T, Latched And Momentary, 5A, 24VDC, Solder/quick Connect Terminal, Rocker Actuator, Panel Mount

KL44-1R4AXABA222NXX Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAPEM
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator typeROCKER
body width24 mm
body height35.5 mm
Body length or diameter46.5 mm
Maximum contact current (DC)5 A
Contact (DC) maximum rated R load5A@24VDC
Maximum contact voltage (DC)24 V
Electrical life100000 Cycle(s)
illuminationGREEN AND RED LED
JESD-609 codee4
Manufacturer's serial numberKL
Installation featuresPANEL MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
method of packingBULK
surface mountNO
Switch actionLATCHED AND MOMENTARY
switch functionDP3T
Switch typeROCKER SWITCH
Terminal surfaceSilver (Ag)
Termination typeSOLDER/QUICK CONNECT
KL series
Locking rocker switches
Distinctive features
Unlocking actuator
Protection frames
Unlocking actuator
Each KL rocker switch includes an unlocking actuator.
This actuator must be pressed to activate the protected function of the rocker.
Moreover, two frames protect the unlocking actuator from untimely activation.
This intuitive and secured ergonomics is patented by APEM.
2 position versions
(electrical functions 1, 5 and 6)
Press unlocking actuator
to reach the protected position
Press opposite part of actuator
to leave the protected position
Á
Á
3 position versions
(electrical functions 7, 8, 9 4, 4-1R)
Press unlocking actuator
to reach the protected position
Press opposite part of actuator
to leave the protected position
Á
Á
Á
12
www.apem.com
APEM
LIS3DH chip problem consultation
[table=98%] [tr][td][color=#444444]Hello everyone, I found a problem when I was doing LIS3DH motion detection. [/color][color=#444444]After configuring the registers of LIS3DH (configuring the motion ...
lskam stm32/stm8
The MCU cannot run in DC-DC mode of BLUENRG-1
In the DC-DC mode of BLUENRG, the voltage output is only about 0.5V, and the output of LDO is also only about 0.5V. The MCU cannot operate normally, and the SWD interface cannot be detected using J-li...
suwithin ST - Low Power RF
My emergency light is fully completed. See the picture.
All the components I used are from MAXIM. Although the workmanship is not very particular, you can take a look at them for reference. The pictures were supposed to be uploaded tomorrow, but because my...
ddllxxrr DIY/Open Source Hardware
How to debug nandflash?? (as the title says software debugging)
Anyone who has done this before, please give me some tips. Thanks....
yangjunweimail Embedded System
Pull-up and pull-down resistors
Sometimes the unused pins of a chip cannot be left floating, and a pull-up resistor or a pull-down resistor is needed to make it at a high or low level. Why not connect it directly to the power supply...
zhonghuadianzie Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2558  733  323  1656  2004  52  15  7  34  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号