EEWORLDEEWORLDEEWORLD

Part Number

Search

54101-T10-15

Description
Board Connector, 15 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size206KB,2 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54101-T10-15 Overview

Board Connector, 15 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle,

54101-T10-15 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid1604620403
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL6.83
Other featuresPOLY BAG PACKAGING
body width0.095 inch
subject depth0.1 inch
body length1.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN LEAD (150) OVER NICKEL
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
DIN complianceNO
Dielectric withstand voltage1500VAC V
Filter functionNO
IEC complianceNO
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialPOLYETHYLENE
JESD-609 codee0
MIL complianceNO
Plug contact pitch0.1 inch
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature130 °C
Minimum operating temperature-65 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
Plating thickness150u inch
Rated current (signal)3 A
GuidelineUL, CSA
Terminal length0.15 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts15
UL Flammability Code94V-0
PDM: Rev:U
STATUS:
Released
Printed: Dec 12, 2008
.
Principle and Application of Fieldbus Temperature Transmitter
I. Introduction The rapid development of information technology has led to changes in the structure of automation systems, and has gradually formed an enterprise information system based on network in...
songbo Embedded System
Help: How to use Altera FFT IP core on FPGA board
I use FPGA to implement a spectrum analyzer and use the on-chip FFP IP core to perform spectrum analysis. I calculate the square sum of the real and imaginary parts and take the logarithm to generate ...
when_Qi FPGA/CPLD
MPLAB editor has red lines everywhere
The code is all red line alarm, but the compilation can pass, please solve it... It affects the programming too much, I thought it was all wrong...
apleilx Microchip MCU
How to remove the seal?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:17[/i] It has just been blocked, how can I unblock it?...
bophic Electronics Design Contest
[Homemade op amp] Can anyone recommend some books or materials on making op amps? [I would like to thank TAT]
Because I need to make an op amp myself recently, but I feel that the static operating points are not set well, and the effect is not good. . What I mean by making an op amp is to use transistors dire...
cinbow Analog electronics
Help post: About IR2110 driver problem
[i=s]This post was last edited by paulhyde on 2014-9-15 03:48[/i] I recently built a IR2110 driver circuit. When I used an oscilloscope to look at the low-end output, the waveform was a normal square ...
DairyQ Electronics Design Contest

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 188  1254  2890  1213  173  4  26  59  25  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号