EEWORLDEEWORLDEEWORLD

Part Number

Search

TDA9885HN/V5

Description
I2C-bus controlled single and multistandard alignment-free IF-PLL demodulators
CategoryAnalog mixed-signal IC    Consumption circuit   
File Size239KB,56 Pages
ManufacturerNXP
Websitehttps://www.nxp.com
Environmental Compliance
Download Datasheet Parametric View All

TDA9885HN/V5 Overview

I2C-bus controlled single and multistandard alignment-free IF-PLL demodulators

TDA9885HN/V5 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerNXP
Parts packaging codeQFN
package instructionHVQCCN, LCC32,.2SQ,20
Contacts32
Reach Compliance Codeunknow
Commercial integrated circuit typesAUDIO/VIDEO DEMODULATOR
Demodulation typeAM/FM
harmonic distortion0.5%
JESD-30 codeS-PQCC-N32
length5 mm
Number of functions1
Number of terminals32
Maximum operating temperature70 °C
Minimum operating temperature-20 °C
Output voltage nominal (AM)500 mV
Nominal output voltage (FM)540 mV
Package body materialPLASTIC/EPOXY
encapsulated codeHVQCCN
Encapsulate equivalent codeLCC32,.2SQ,20
Package shapeSQUARE
Package formCHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE
power supply5 V
Certification statusNot Qualified
Maximum seat height1 mm
Maximum slew rate70 mA
Maximum supply voltage (Vsup)5.5 V
Minimum supply voltage (Vsup)4.5 V
surface mountYES
Temperature levelOTHER
Terminal formNO LEAD
Terminal pitch0.5 mm
Terminal locationQUAD
width5 mm
TDA9885; TDA9886
I
2
C-bus controlled single and multistandard alignment-free
IF-PLL demodulators
Rev. 03 — 16 December 2008
Product data sheet
1. General description
The TDA9885 is an alignment-free multistandard (PAL and NTSC) vision and sound
IF signal Phase-Locked Loop (PLL) demodulator for negative modulation only and
FM processing.
The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and
sound IF signal PLL demodulator for positive and negative modulation, including sound
AM and FM processing.
2. Features
I
5 V supply voltage
I
Gain controlled wideband Vision Intermediate Frequency (VIF) amplifier, AC-coupled
I
Multistandard true synchronous demodulation with active carrier regeneration: very
linear demodulation, good intermodulation figures, reduced harmonics, and excellent
pulse response
I
Gated phase detector for L and L-accent standard
I
Fully integrated VIF Voltage-Controlled Oscillator (VCO), alignment-free, frequencies
switchable for all negative and positive modulated standards via I
2
C-bus
I
Digital acquisition help, VIF frequencies of 33.4 MHz, 33.9 MHz, 38.0 MHz, 38.9 MHz,
45.75 MHz and 58.75 MHz
I
4 MHz reference frequency input: signal from PLL tuning system or operating as
crystal oscillator
I
VIF Automatic Gain Control (AGC) detector for gain control, operating as peak sync
detector for negative modulated signals and as a peak white detector for positive
modulated signals
I
Precise fully digital Automatic Frequency Control (AFC) detector with 4-bit
digital-to-analog converter, AFC bits readable via I
2
C-bus
I
TakeOver Point (TOP) adjustable via I
2
C-bus or alternatively with potentiometer
I
Fully integrated sound carrier trap for 4.5 MHz, 5.5 MHz, 6.0 MHz and 6.5 MHz,
controlled by FM-PLL oscillator
I
Sound IF (SIF) input for single reference Quasi Split Sound (QSS) mode, PLL
controlled
I
SIF AGC for gain controlled SIF amplifier, single reference QSS mixer able to operate
in high performance single reference QSS mode and in intercarrier mode, switchable
via I
2
C-bus
I
AM demodulator without extra reference circuit
I
Alignment-free selective FM-PLL demodulator with high linearity and low noise
Angle control algorithm of slope sensor
When using the slope sensor, how is the angle controlled? Does anyone have an algorithm for this? Please give me some advice:congratulate:...
jonlovehanxu MCU
Has anyone made a camera driver based on the 2440 camera interface?
As the title says, I am making a camera driver based on camera interface (Samsung has provided a benchmark driver, not USB). Now I can write data to the camera IC through SCCB, and the preview image h...
grace811226 Embedded System
ADuC 814, can I write data into 8kb FLASH, and what instruction can be used to read the data at a specified address?
Now I only found a way to download the program to FLASH through the serial port, and there are instructions to read and write the 640B data storage area. But I want to put both the program and data in...
stone8530 Embedded System
Show the WEBENCH design process + AC power supply output 5V2A circuit solution
[i=s]This post was last edited by qwqwqw2088 on 2014-7-28 17:25[/i] 1. Title: AC power supply output 5V2A circuit solution This design can also be used as a mobile phone high current charger solution ...
qwqwqw2088 Analogue and Mixed Signal
How to simulate external interrupt in Keil?
I want to use an external interrupt to start the timer. The code can be sent to the hardware to achieve it. But using GPIO_SetBits() in software does not work. The timer cannot be started, but it can ...
vincent.liu stm32/stm8
About Common Emission Amplification
[img]http://C:\Documents and Settings\MS\Desktop[/img] Please experts analyze this for me, thank you. I have been thinking about it for a few days but still can't figure out the reason. I don't know i...
dspyq Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2915  2923  1551  1251  460  59  32  26  10  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号