Feature - No dead cycles between write and read cycles
Internally synchronized output buffer enable eliminates the
need to control
OE
Single R/W (READ/WRITE) control pin
Positive clock-edge triggered address, data, and control
signal registers for fully pipelined applications
4-word burst capability (interleaved or linear)
Individual byte write (BW
1
-
BW
4
) control (May tie active)
Three chip enables for simple depth expansion
3.3V power supply (±5%)
2.5V I/O Supply (V
DDQ
)
Power down controlled by ZZ input
Packaged in a JEDEC standard 100-pin plastic thin quad and
flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch
ball grid array (fBGA)
The IDT71V65602/5802 are 3.3V high-speed 9,437,184-bit
(9 Megabit) synchronous SRAMs. They are designed to eliminate dead
bus cycles when turning the bus around between reads and writes, or
writes and reads. Thus, they have been given the name ZBT
TM
, or Zero
Bus Turnaround.
Description
Address and control signals are applied to the SRAM during one clock
cycle, and two cycles later the associated data cycle occurs, be it read or write.
The IDT71V65602/5802 contain data I/O, address and control signal
registers. Output enable is the only asynchronous signal and can be used to
disable the outputs at any given time.
A Clock Enable (CEN) pin allows operation of the IDT71V65602/5802
to be suspended as long as necessary. All synchronous inputs are ignored
when (CEN) is high and the internal device registers will hold their previous
values.
There are three chip enable pins (CE
1
, CE
2
,
CE
2
) that allow the
user to deselect the device when desired. If any one of these three are not
asserted when ADV/LD is low, no new memory operation can be initiated.
However, any pending data transfers (reads or writes) will be completed. The
data bus will tri-state two cycles after chip is deselected or a write is initiated.
The IDT71V65602/5802 have an on-chip burst counter. In the burst
mode, the IDT71V65602/5802 can provide four cycles of data for a single
address presented to the SRAM. The order of the burst sequence is defined
by the
LBO
input pin. The
LBO
pin selects between linear and interleaved burst
sequence. The ADV/LD signal is used to load a new external address (ADV/
LD
= LOW) or increment the internal burst counter (ADV/LD = HIGH).
The IDT71V65602/5802 SRAM utilize IDT's latest high-performance
CMOS process, and are packaged in a JEDEC Standard 14mm x 20mm 100-
pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array (BGA)
and a 165 fine pitch ball grid array (fBGA).
Pin Description Summary
A
0
-A
18
CE
1
, CE
2
,
CE
2
OE
R/W
CEN
BW
1
,
BW
2
,
BW
3
,
BW
4
CLK
ADV/LD
LBO
ZZ
I/O
0
-I/O
31
, I/O
P1
-I/O
P4
V
DD
, V
DDQ
V
SS
Address Inputs
Chip Enables
Output Enable
Read/Write Signal
Clock Enable
Individual Byte Write Selects
Clock
Advance burst address / Load new address
Linear / Interleaved Burst Order
Sleep Mode
Data Input / Output
Core Power, I/O Power
Ground
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
I/O
Supply
Supply
Synchronous
Synchronous
Asynchronous
Synchronous
Synchronous
Synchronous
N/A
Synchronous
Static
Asynchronous
Synchronous
Static
Static
5303 tbl 01
ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola, Inc.
[color=#333333][backcolor=rgb(245, 248, 253)][font="][size=15px]The victory of AlphaGo in the Go game officially brought artificial intelligence into the public eye. DeepMind (an artificial intelligen...
The e-book tutorial our teacher sent today is very detailed. Many commonly used modules of microcontrollers are included. Please allow me to make some money. Please forgive me....
I want to use MFC to write a PC Bluetooth software with the functions of searching, connecting, encrypting and transferring files. I hope the experts can give me some information about MFC Bluetooth p...
scancodetovirtualkey, I looked at the source code and it is calling *puiVk = MapVirtualKey(*puiSc, MAP_SC_TO_VK); but I can't find this function. Does anyone know, please help me solve it.```...
I built a solution using Visual Studio C#. I want to read the XML in the same directory as the exe file. How can I read it? I have never used WINCE before. Please give me some advice....
The TIA Portal software's shift instructions shift the contents of an accumulator bit by bit to the left or right. The number of bits shifted is determined by N. A left shift of N bits multiplies t...[Details]
Dual-mode inverters can operate both in conjunction with the grid and independently. These inverters can inject excess energy from renewable energy and storage devices into the grid, and withdraw p...[Details]
The jammer is a signal blocker, mainly composed of a chip and a radio transmitter. When the car owner presses the remote control lock button, the jammer interferes with the electronic lock receivin...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
summary
There are multiple approaches to making industrial systems more intelligent, including applying artificial intelligence (AI) technology at the edge and in the cloud to sensor...[Details]
On August 25th, Apple's expansion in India encountered new troubles. According to Bloomberg, Foxconn Technology Group has recalled approximately 300 Chinese engineers from India, further hindering ...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
In the summer of 2025, BlueOval SK, a joint venture between Ford and SK On, officially started production at its first battery factory in Kentucky.
According to the original plan, this w...[Details]
The complexity of the integrated circuits (ICs) used in electronic systems in vehicles is increasing. They aim to execute artificial intelligence (AI) algorithms to control autonomous driving funct...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
Industrial computers with GPUs leverage powerful parallel processing to build deep learning models to analyze and respond to optical inputs. The systems develop an understanding of visual data to i...[Details]
Batteries, at the core of new energy vehicles, are crucial to vehicle performance and range. Existing automotive batteries are categorized into lead-acid and lithium batteries. Currently, new energ...[Details]
The range of an electric vehicle is crucial to the driving experience, and range anxiety is a common headache when driving an electric vehicle. Although the latest electric vehicles can achieve a r...[Details]
Electric vehicles will revolutionize transportation, changing fuel consumption, carbon emissions, costs, maintenance, and driving habits. Currently, a major selling point for electric vehicles is t...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
