EEWORLDEEWORLDEEWORLD

Part Number

Search

Q14P2CXXB02-0ST

Description
Visible LED,
CategoryLED optoelectronic/LED    photoelectric   
File Size514KB,5 Pages
ManufacturerAPEM
Environmental Compliance
Download Datasheet Parametric View All

Q14P2CXXB02-0ST Overview

Visible LED,

Q14P2CXXB02-0ST Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAPEM
Reach Compliance Codecompliant
colorBLUE
ConfigurationSINGLE
Lens typeDIFFUSED
Installation featuresRADIAL MOUNT
Number of functions1
Number of terminals2
Optoelectronic device typesSINGLE COLOR LED
total height4.75 mm
method of packingBULK
Maximum reverse voltage5 V
shapeROUND
surface mountNO
Terminal pitch2.5 mm
Q SERIES Ø14mm (.551") Panel Mount LED Indicators
Distinctive features and specification
Q14_VOYC1609R2US
Features
• 14mm panel mounting LED indicator
• 10mm colored diffused epoxy lens or 10mm water clear super bright LEDs
• Plated brass bezel finished in bright chrome,
black chrome or satin grey and moulded polycarbonate rear body
• Prominent recessed and flush bezel styles
• Custom engraving available
• 2VDC – 220VAC
• (2.8 x 0.8) solder lug/Faston terminals, pins or (200mm long) wire terminations
• IP67 sealing option (EN60529)
• Supplied with fixing nut and spring washer
NB: UL Recognized Component
TECHNICAL SPECIFICATIONS
Voltage
02 (No Resistor)
6VDC
12VDC
24VDC
28VDC
110VAC
220VAC
Operating Voltage
(Min to Max)
1.8 to 3.3VDC
5.4 to 6.6VDC
10.8 to 13.2VDC
21.6 to 26.4VDC
25.2 to 30.8VDC
99 to 121VAC
207 to 253VAC
Operating Current
(Typical All Types)
20mA max*
20mA
20mA
20mA
20mA
6mA
3mA
Max Reverse Voltage:
5V
Viewing Angle:
30–100°
(dependant on model)
Life Expectancy:
100,000 hours
Temperature Range:
–40 to +85°C
(operating & storage)
Torque:
75cNm
Ø 14.00 +0.15/-0.0
17,00 0,669
AF
3,00 0,118
PANEL CUTOUT
M14 x 1,0 THREAD
Standard LED Intensity
Prominent and Recessed
Flush
Forward Voltage
HE Red
80mcd
10mcd
2.0V
Green
60mcd
5mcd
2.2V
Yellow
50mcd
4mcd
2.1V
Blue
540mcd
100mcd
3.3V
White
1000mcd
150mcd
3.3V
Orange
80mcd
200mcd
2.0V
Bi-color (Typical) (Red/Green)
15/15mcd
14/10mcd
2.0V/2.2V
Tri-color (Typical) (Red/Green/Yellow)
60/50/50mcd
15/10/30mcd
2.0V/2.2V/2.1V
Bi-color - The color is changed by reversing the polarity of the supply voltage.
Tri-color - The indicator has red and green LEDs, when both connected yellow is produced.
Super Bright LED
HE Red
Green
Yellow
Blue
White
Orange
Hyper Bright LED
HE Red
Green
Yellow
Orange
Prominent and Recessed
17,000mcd
11,000mcd
4,000mcd
2,500mcd
4,400mcd
2800mcd
Prominent and Recessed
2,800mcd
2,200mcd
1,300mcd
850mcd
Flush
2,000mcd
680mcd
350mcd
250mcd
250mcd
300mcd
Flush
800mcd
250mcd
250mcd
200mcd
Forward Voltage
2.2V
3.5V
2.3V
3.3V
3.3V
2.1V
Forward Voltage
2.1V
3.2V
2.0V
2.1V
Luminous intensity will be reduced with lower operating current.
Note: The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy.
The company reserves the right to change specifications without notice.
* Customer to supply resistor for desired operating current.
Luminous intensity is measured at 20mA on a discrete LED unless otherwise stated.
Luminous intensities and color shades of white LEDs may vary within a batch.
LED characteristics are dependent upon environmental conditions. Therefore published data should be considered nominal.
APEM
www.apem.com
1
STM32L051's ADC conversion is inaccurate after wakeup
[font=宋体][size=5]After waking up from STM32L051 stop mode, the voltage converted by ADC is inaccurate. It needs to be initialized before each conversion. Has anyone encountered a similar situation? Pl...
943614033 stm32/stm8
STM32F429Discovery oscilloscope test heart rate
I was testing the pulse sensor at night and wondered if the STM32F429Discovery oscilloscope could be used to measure the waveform, so I tried it. Set the CH1 input, T=500ms, and adjust the offsetThe o...
dcexpert stm32/stm8
Question about bootloader interrupt vector
After reading the bootloader, I have some doubts: 1. When an exception occurs, the interrupt vector table is forced to jump by hardware according to the exception, and then the service program address...
taotaotalk Embedded System
Distribution analysis and maintenance of common faults in plc process control systems
In order to extend the life of the PLC control system, it is necessary to have a clear estimate of the equipment consumption and the failure points of the components and equipment in the system design...
frozenviolet Industrial Control Electronics
Discussing WINCE TCP/IP programming?
The PC version of TCP/IP has controls, but the WINCE version does not. It only has a SOCKET. Now some industrial control systems use TCP/IP, big data, real-time, and wireless. The serial port is also ...
tysym Embedded System
After installing the USB filter driver, how to solve the blue screen after restart?
Following the example in Chapter 22 of Zhang Fan's "Detailed Explanation of Windows Driver Development Technology", I made a USB filter driver and disabled the USB drive. After installing it and resta...
kunlun Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 680  2151  969  2157  657  14  44  20  10  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号