Enhanced N channel FET with no inherent diode to Vcc
16:8 multiplexer function with zero delay
5Ω bidirectional switches connect inputs to outputs
Ω
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
Direct bidirectional connection for mux, demux
25Ω resistors for low noise
Ω
Available in QSOP package
DESCRIPTION:
The QS32390 provides a 16:8 multiplexer logic switch. The QS32390 has
an internal 25Ω resistor to reduce reflection noise in high-speed applica-
tions. The enable inputs connect one of two inputs to the common I/O pin,
respectively. The multiplexer function can be used to select and route logic
signals for zero delay, isolate bus capacitance, form crossbar switches, etc.
Mux/Demux devices provide an order of magnitude faster speed than
equivalent logic devices.
The QS32390 is characterized for operation at -40°C to +85°C.
APPLICATIONS:
• Video, audio, graphics switching, muxing
• Hot-swapping, hot-docking
• Voltage translation (5V to 3.3V)
FUNCTIONAL BLOCK DIAGRAM
A
0
AB
0
A
7
AB
7
AEN
B
0
B
7
BEN
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
c
2011 Integrated Device Technology, Inc.
FEBRUARY 2011
1
DSC-5752/5
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
A
0
B
0
AB
0
A
1
B
1
AB
1
A
2
B
2
AB
2
A
3
B
3
AB
3
AEN
GN
D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
CC
A
7
B
7
AB
7
A
6
B
6
AB
6
A
5
B
5
AB
5
A
4
B
4
AB
4
BEN
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
TERM
(2)
Description
Supply Voltage to Ground
Max
–0.5 to +7
–0.5 to +7
–0.5 to +7
–3
120
0.5
–65 to +150
Unit
V
V
V
V
mA
W
°C
V
TERM
(3)
DC Switch Voltage Vs
V
TERM
(3)
DC Input Voltage V
IN
V
AC
I
OUT
P
MAX
T
STG
AC Input Voltage (pulse width
≤
20ns)
DC Output Current
Maximum Power Dissipation (T
A
= 85°C)
Storage Temperature
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. Vcc terminals.
3. All terminals except Vcc.
CAPACITANCE
QSOP
TOP VIEW
Pins
Control Pins
Quickswitch Channels
(Switch OFF)
(T
A
= +25°C, f = 1.0MH
Z
, V
IN
= 0V, V
OUT
= 0V)
Typ.
4
Demux
Mux
5
9
Max.
(1)
5
7
10
Unit
pF
pF
NOTE:
1. This parameter is measured at characterization but not tested.
PIN DESCRIPTION
Pin Names
A
0
- A
9
B
0
- B
9
AEN, BEN
I/O
I/O
I/O
I
Bus A
Bus B
Bus Switch Enable
Description
FUNCTION TABLE
(1)
AEN
H
L
H
L
BEN
H
H
L
L
A
0
- A
9
Off
On
Off
On
B
0
- B
9
Off
Off
On
On
A to AB
B to AB
A, B to AB
Function
Disconnect
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
2
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 5.0V ±5%
Symbol
V
IH
V
IL
I
IN
I
OZ
R
ON
(3)
V
P
Parameter
Input HIGH Level
Input LOW Level
Off-State Output Current (Hi-Z)
Switch ON Resistance
Pass Voltage
(2)
Test Conditions
Guaranteed Logic HIGH for Control Pins
Guaranteed Logic LOW for Control Pins
0V
≤
V
OUT
≤
V
CC
, Switches OFF
V
CC
= Min., V
IN
= 0V, I
ON
= 30mA
V
CC
= Min., V
IN
= 2.4V, I
ON
=15mA
V
IN
= V
CC
= 5V, I
OUT
= -5μA
Min.
2
—
—
—
15
15
3.7
Typ.
(1)
—
—
—
—
20
19
4
Max.
—
0.8
±1
±1
35
40
4.2
Unit
V
V
μA
μA
Ω
V
Input LeakageCurrent (Control Inputs)
(2)
0V
≤
V
IN
≤
V
CC
NOTES:
1. Typical values are at V
CC
= 5.0V, T
A
= 25°C.
2. Pass Voltage is guaranteed but not production tested.
3. R
OUT
changed on March 8, 2002. See rear page for more information.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 5V
80
R
ON
(ohms)
70
60
50
40
30
20
10
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
V
IN
(Volts)
3
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
ΔI
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current per Control Input HIGH
(2)
Dynamic Power Supply Current per MHz
(3)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or Vcc, f = 0
V
CC
= Max., V
IN
= 3.4V, f = 0
V
CC
= Max., A, B, and AB pins open
Control Inputs Toggling at 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TLL driven input (V
IN
= 3.4V, control inputs only). A, B, and AB pins do not contribute to
ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A, B, and AB I/Os generate no
significant AC or DC currents as they transition. This parameter is guaranteed but not production tested.
Max.
3
1.5
0.25
Unit
μA
mA
mA/MHz
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C, V
CC
= 5.0V ± 5%;
C
LOAD
= 50pF, R
LOAD
= 500Ω unless otherwise noted.
Symbol
t
PLH
t
PHL
t
PZH
t
PZL
t
PHZ
t
PLZ
Data Propagation Delay
(2,4)
AxBx to CxDx, CxDx to AxBx
Switch Turn-on Delay
BE
to Ax, Bx, Cx, Dx
Switch Turn-off Delay
(2)
BE
to Ax, Bx, Cx, Dx
—
—
5.5
ns
Parameter
Min.
(1)
—
1.5
Typ.
—
—
Max.
1.25
(3)
7.5
Unit
ns
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The time constant for the switch alone is of the order of 1.25ns for C
L
= 50pF.
4. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. Since this time constant is much smaller
than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined
by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
4
IDTQS32390
HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Blank
8
QG
Tube or Tray
Tape and Reel
Quarter Size Outline Package - Green
32390
High Speed CMOS QuickSwitch 16:8 Multiplexer
As per PCN L0201-02, the Output Resistance (R
ON
) specifications have changed as of March 8, 2002. The original specifications were:
Parameter
R
ON
Description
V
CC
= Min, V
IN
= 0V, I
ON
= 30mA
V
CC
= Min, V
IN
= 2.4V, I
ON
= 15mA
Min.
20
24
Typ.
28
35
Max.
40
48
Unit
Ω
Datasheet Document History
02/09/2011
Pg. 5
Updated the ordering information by removing the "IDT" notation, non RoHS part and by adding
Design an automatic flag raising and lowering system that can automatically raise and lower the flag. The mechanical model of the system is shown in Figure 1. The raising and lowering of the flag is d...
Is there such a relay, four groups of signals, one state, 1 and 2 are connected, 3 and 4 are connected, another state. 1 and 4 are connected, 2 and 3 are connected. Although two double-pole double-thr...
I feel like I am about to die, and I can't help but complain. The work is too "idle"!!! All day long, I either arrange workshop work, go out to upgrade the program, or do various chip research, and th...
Abstract In this paper,simply describes some key technololgies used for the Ku/X band converter,and gives practical scheme for the converter and test results. Dey word converter; PLD; frequency multip...
The relationship between EMCP/EMMC/MCP/DRAM/FLASH: In three sentences: MCP is NAND Flash+DRAM; eMMC is NAND Flash+Controller; eMCP is eMMC+DRAM. 1. Memory chip manufacturers: Korean: Samsung, Hynix (H...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
The future energy storage hotspot is not coal or iron ore, but lithium. This lightest metal in nature may be the heaviest resource in the future energy landscape. China launched an ambitious electr...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
