803-43-074-61-002-100 datasheet, PDF

Datasheet> All Categories > The connector> The connector> 803-43-074-61-002-100

803-43-074-61-002-100: DescriptionBoard Connector, 74 Contact(s), 2 Row(s), Female, Straight, Press Fit Terminal, Socket, ROHS COMPLIANT; CategoryThe connector The connector; File Size210KB，1 Pages; ManufacturerMill-Max; Websitehttps://www.mill-max.com; Environmental Compliance

Download Datasheet Parametric View All

803-43-074-61-002-100 Overview

Board Connector, 74 Contact(s), 2 Row(s), Female, Straight, Press Fit Terminal, Socket, ROHS COMPLIANT

803-43-074-61-002-100 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compli
ECCN code	EAR99
Body/casing type	SOCKET
Connector type	BOARD CONNECTOR
Contact to complete cooperation	GOLD (30) OVER NICKEL (100)
Contact completed and terminated	TIN (200)
Contact point gender	FEMALE
Contact material	NOT SPECIFIED
DIN compliance	NO
Filter function	NO
IEC compliance	NO
JESD-609 code	e3
MIL compliance	NO
Manufacturer's serial number	803
Mixed contacts	NO
Installation method	STRAIGHT
Installation type	BOARD
Number of rows loaded	2
Options	GENERAL PURPOSE
Terminal pitch	2.54 mm
Termination type	PRESS FIT
Total number of contacts	74
Base Number Matches	1

Preview

Download Datasheet

View All

INTERCONNECTS

Solderless Press-Fit

Double Row

•

The unique compliant tail pins conform to

.040”+.003” finished hole without stressing

inner layers. Patent No. 4,799,904

•

Series 802 pin headers are offered in two

tail lengths for .060”-.100” (MM #5601)

and .090”-.130” (MM #5602) thick panels.

See page 178 for details.

•

Series 803 sockets MM #4614 or #4615

use Hi-Rel, 6-finger BeCu #47 contacts

rated at 4.5 amps. Receptacles accept

.030” diameter pins & .025” square pins.

See page 211 for details.

Series 802, 803

Fig. 1

•

Insulators are high temp. thermoplastic.

Ordering Information

Compliant Tail Pin Header

for .060 - .100” thick boards

Fig. 1

802-XX-0 _ _-61-001000

Specify # of pins

02-64

Fig. 2

Compliant Tail Pin Header

for .090 - .130” thick boards

802-XX-0 _ _-62-001000

Specify # of pins

XX= Plating Code

See Below

02-64

For RoHS compliance

select plating code.

200μ” Sn

SPECIFY PLATING CODE XX=

10μ” Au

200μ” Sn/Pb

Pin Plating

Fig. 3

Compliant Tail Socket

for .060 - .100” thick boards

803-XX-_ _ _-61-001000

Specify # of pins

002-100

Fig. 4

Compliant Tail Socket

for .090 - .130” thick boards

803-XX-_ _ _-62-001000

Specify # of pins

XX= Plating Code

See Below

002-100

For RoHS compliance

select plating code.

200µ”Sn/Pb

SPECIFY PLATING CODE XX=

10µ” Au

30µ” Au

10µ” Au

30µ” Au

10µ” Au

Sleeve (Pin)

200µ” Sn/Pb

200µ” Sn/Pb 200µ”Sn/Pb

200µ”Sn

30µ” Au

200µ”Sn

Fig. 4

Contact (Clip)

w w w. m i l l - m a x . c o m

516-922-6000

Recommended Resources

Four-channel remote control switch circuit a

Negative voltage output voltage stabilizing circuit composed of 7800 series

Refrigerator door closing prompt circuit

Biogas leak detection circuit

Electronic relay phase failure protection circuit

Help: How to collect three-phase voltage of brushless DC motor by multiplying bus voltage by duty cycle?: Does anyone know this method? In the PM sensorless sample program provided by TI, there is a permanent magnet synchronous motor that uses this method to obtain three-phase voltage, but I don't know ho...; miumiuxi Microcontroller MCU

Solution to the problem that the STM32 ST-LINK Utility cannot connect to the microcontroller "Can not connect to target!": When I used the STM32 ST-LINK Utility to connect to the microcontroller today, the following error message popped up: "Can not connect to target!Please select "Connect Under Reset" mode from Target-Se...; littleshrimp stm32/stm8

Must read before asking questions in DSP section!!!: If you want your questions to get the attention of TI experts and senior engineers in the forum as soon as possible, please pay special attention to the following points:1. Please be sure to indicate ...; EEWORLD社区 DSP and ARM Processors

Gooogleman, please come in. NAND boot code problem.: NAND boot code ldr r0, =BWSCON ldr r0, [r0] ands r0, r0, #6 ;OM[1:0] != 0, NOR FLash boot bne copy_proc_beg ;don't read nand flash' adr r0, ResetEntry ;OM[1:0] == 0, NAND FLash boot cmp r0, #0 ;if use...; zoujy518 Embedded System

Has anyone seen these flip-flops before? Do you know their characteristic equations?: [img]http://hi.eeworld.net/attachment/200911/22/5108_1258896385fnjB.jpg[/img] [img]http://hi.eeworld.net/attachment/200911/22/5108_1258896384sFbI.jpg[/img] [img]http://hi.eeworld.net/attachment/200911...; yangyang_2008 Embedded System

This is China's first E-marker chip that has obtained USB-IF certification: [size=4]At present, the USB PD fast charging protocol has been widely used in products of first-line brands such as Apple, Google, Huawei, Xiaomi, and Samsung. The next generation of iPhones will be e...; qwqwqw2088 Analogue and Mixed Signal

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components