R1162x SERIES
Non-promotion
3-MODE 150mA LDO REGULATOR
NO.EA-110-130415
OUTLINE
The R1162x Series consist of CMOS-based voltage regulator ICs with high output voltage accuracy and low
supply current. Each of these voltage regulator ICs consists of a voltage reference unit, an error amplifier,
resistors for setting output voltage, a current limit circuit, and so on. The output voltage is internally fixed with
high accuracy.
These ICs perform with the chip enable function and realize a standby mode with ultra low supply current. To
prevent the destruction by over current, the current limit circuit is included. The R1162x Series have 3-mode.
One is standby mode with CE or standby control pin. Other two modes are realized with ECO pin. Fast Transient
Mode (FT mode) and Low Power Mode (LP mode) are alternative with ECO pin. Consumption current is reduced
at Low Power Mode compared with Fast Transient Mode. The output voltage is maintained between FT mode
and LP mode.
Since the packages for these ICs are SOT-23-5 and SON1612-6 packages, high density mounting of the ICs
on boards is possible.
FEATURES
•
Supply Current .......................................................Typ. 5.5μA (Low Power Mode),
Typ. 70μA (Fast Transient Mode)
•
Standby Current .....................................................Typ. 0.1μA
•
High Ripple Rejection ............................................Typ. 70dB (f=1kHz, Fast Transient Mode)
Typ. 60dB (f=10kHz, Fast Transient Mode)
•
Input Voltage Range ..............................................2.0V to 6.0V
•
Output Voltage Range............................................1.5V to 4.0V (0.1V steps)
(
For other voltages, please refer to MARK INFORMATIONS.)
•
Output Voltage Accuracy........................................±2.0% (±3.0% at Low Power Mode)
•
Temperature-Drift Coefficient of Output Voltage ....Typ.
±100ppm/°C
•
Dropout Voltage .....................................................Typ. 0.25V (I
OUT
=150mA
, V
OUT
=2.8V)
•
Line Regulation ......................................................Typ. 0.02%/V
•
Package ...............................................................SON1612-6, SOT-23-5
•
Built-in fold-back protection circuit .........................Typ. 40mA (Current at short mode)
•
Performs with Ceramic Capacitors ........................C
IN
=1.0μF,C
OUT
=0.47μF
-
n
o
N
o
r
p
o
m
n
io
t
APPLICATIONS
•
Precision Voltage References.
•
Power source for electrical appliances such as cameras, VCRs and hand-held communication equipment.
•
Power source for battery-powered equipment.
1
R1162x
non-promotion
BLOCK DIAGRAM
R1162xxx1B
R1162xxx1D
ECO
ECO
V
DD
V
OUT
V
DD
V
OUT
Vref
Current Limit
Vref
Current Limit
CE
GND
CE
SELECTION GUIDE
The output voltage, auto discharge function, and package, etc. for the ICs can be selected at the user’s
request.
Product Name
R1162Dxx1∗-TR-FE
R1162Nxx1∗-TR-FE
Package
Quantity per Reel
4,000 pcs
3,000 pcs
SON1612-6
SOT-23-5
xx : The output voltage can be designated in the range from 1.5V(15) to 4.0V(40) in 0.1V steps.
(For other voltages, please refer to MARK INFORMATIONS.)
∗
: The auto discharge function at off state are options as follows.
(B) without auto discharge function at off state
(D) with auto discharge function at off state
These products will be discontinued in the future. We advise you to select other products.
-
n
o
N
o
r
p
o
m
Pb Free
Yes
Yes
n
io
t
GND
Halogen Free
Yes
Yes
The products scheduled to be discontinued : "Non-promotion"
2
R1162x
non-promotion
ABSOLUTE MAXIMUM RATINGS
Symbol
V
IN
V
ECO
V
CE
V
OUT
I
OUT
P
D
Topt
Tstg
Input Voltage
Input Voltage (ECO Pin)
Input Voltage (
CE
/ CE Pin)
Output Voltage
Output Current
Power Dissipation (SOT-23-5)
∗
Power Dissipation (SON1612-6)
∗
Operating Temperature Range
Storage Temperature Range
Item
Rating
6.5
−0.3
to 6.5
−0.3
to 6.5
−0.3
to V
IN
+0.3
180
420
500
−40
~ 85
−55
~ 125
Unit
V
V
V
V
mA
mW
MW
°C
°C
∗)
For Power Dissipation, please refer to PACKAGE INFORMATION.
ABSOLUTE MAXIMUM RATINGS
Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the
permanent damages and may degrade the life time and safety for both device and system using the device
in the field.
The functional operation at or over these absolute maximum ratings is not assured.
RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS)
All of electronic equipment should be designed that the mounted semiconductor devices operate within the
recommended operating conditions. The semiconductor devices cannot operate normally over the
recommended operating conditions, even if when they are used over such conditions by momentary
electronic noise or surge. And the semiconductor devices may receive serious damage when they continue
to operate over the recommended operating conditions.
-
n
o
N
o
r
p
o
m
n
io
t
4
R1162x
Non-promotion
ELECTRICAL CHARACTERISTICS
•
R1162xxx1B/D
Item
Output Voltage
Conditions
Min.
Typ.
Max.
Topt
=
25°C
Symbol
V
OUT
Unit
ΔV
OUT
I
OUT
ΔV
OUT
/
ΔI
OUT
V
DIF
I
SS1
I
SS2
Output Voltage Deviation
between FT Mode and LP
Mode
Output Current
Load Regulation(FT Mode)
Load Regulation(LP Mode)
Dropout Voltage
Supply Current(FT Mode)
Supply Current(LP Mode)
Istandby Supply Current (Standby)
Line Regulation(FT Mode)
ΔV
OUT
/
ΔV
IN
Line Regulation(LP Mode)
RR
V
IN
ΔV
OUT
/
ΔTopt
I
SC
I
PD
R
PD
V
CEH
V
CEL
en
en
R
LOW
Ripple Rejection(FT Mode)
Input Voltage
Output Voltage
Temperature Coefficient
Short Current Limit
CE Pull-down
Constant Current
ECO Pull-down Resistance
CE, ECO Input Voltage “H”
CE, ECO Input Voltage “L”
Output Noise (Fast Mode)
Output Noise
(Low Power Mode)
Nch On resistance for
auto-discharge
(Applied to D version)
-
n
o
N
V
OUT
V
OUT
V
IN
=
Set V
OUT
+1V
V
ECO
=
V
IN
V
Note 1
1mA
<
I
OUT
<
30mA
×0.98
×1.02
=
=
V
OUT
V
OUT
V
IN
=
Set V
OUT
+
1V V
ECO
=GND
V
Note 2
×0.97
×1.03
1mA
<
I
OUT
<
30mA
=
=
V
IN
=
Set V
OUT
+1V,
I
OUT
=30mA
0.0
1.2
%
−1.2
V
OUT
<
2.0V
=
0.0
(24)
mV
V
OUT
>
2.0V
(−24)
=
150
mA
V
IN
−
V
OUT
=
1.0V
V
IN
=Set
V
OUT
+1V,
V
ECO
=V
IN
20
40
mV
1mA
<
I
OUT
<
150mA
=
=
V
IN
=
Set V
OUT
+1V,V
ECO
=GND
20
45
mV
1mA
<
I
OUT
<
150mA
=
=
Refer to the ELECTRICAL CHARACTERISTICS by OUTPUT VOLTAGE
V
IN
=
Set V
OUT
+1V
70
100
μA
V
ECO
=
V
IN
,
I
OUT
=0mA
V
IN
=
Set V
OUT
+1V
5.5
9.0
μA
V
ECO
=
GND
,
I
OUT
=0mA
0.1
1.0
μA
V
IN
=
V
CE
=
Set V
OUT
+1V
Set V
OUT
+0.5V
<
V
IN
<
6.0V
=
=
0.02
0.10
%/V
I
OUT
=
30mA, V
ECO
=
V
IN
<
1.6V: 2.2V
<
V
IN
<
6.0V
V
OUT
=
=
=
Set V
OUT
+
0.5V
<
V
IN
<
6.0V
=
=
0.05
0.20
%/V
I
OUT
=
30mA, V
ECO
=
GND
V
OUT
<
1.6V: 2.2V
<
V
IN
<
6.0V
=
=
=
f
=
1kHz
70
60
f
=
10kHz,Ripple 0.2Vp-p
dB
V
IN
=
Set V
OUT
+
1V
I
OUT
=
30mA, V
ECO
=
V
IN
2.0
6.0
V
ppm
I
OUT
=
30mA
±100
<
Topt
<
85°C
/°C
−40°C
=
=
40
mA
V
OUT
=
0V
o
r
p
o
m
n
io
t
0.3
2
1.0
0.00
BW
=
10Hz to 100kHz
BW
=
10Hz to 100kHz
V
CE
=0V
5
0.6
30
6.0
0.35
μA
MΩ
V
V
μVrms
μVrms
Ω
30
40
60
5
京公网安备 11010802033920号
EEWORLD
