FUJITSU MICROELECTRONICS
DATA SHEET
DS07-12614-5E
8-bit Proprietary Microcontrollers
CMOS
F
2
MC-8FX MB95100AM Series
MB95108AM/F104AMS/F104ANS/F104AJS/F106AMS/F106ANS/F106AJS/
MB95F108AMS/F108ANS/F108AJS/F104AMW/F104ANW/F104AJW/F106AMW/
MB95F106ANW/F106AJW/F108AMW/F108ANW/F108AJW/FV100D-103
■
DESCRIPTION
The MB95100AM series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
Note : F
2
MC is the abbreviation of FUJITSU Flexible Microcontroller.
■
FEATURE
•
F
2
MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instruction
• Bit manipulation instructions etc.
•
Clock
• Main clock
• Main PLL clock
• Sub clock (for dual clock product)
• Sub PLL clock (for dual clock product)
(Continued)
For the information for microcontroller supports, see the following web site.
This web site includes the
"Customer Design Review Supplement"
which provides the latest cautions on
system development and the minimal requirements to be checked to prevent problems before the system
development.
http://edevice.fujitsu.com/micom/en-support/
Copyright©2006-2009 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2009.3
MB95100AM Series
(Continued)
•
Timer
• 8/16-bit compound timer
×
2 channels
• 16-bit reload timer
• 8/16-bit PPG
×
2 channels
• 16-bit PPG
×
2 channels
• Timebase timer
• Watch prescaler (for dual clock product)
•
LIN-UART
• Full duplex double buffer
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
•
UART/SIO
• Full duplex double buffer
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
2
C
•
I
Built-in wake-up function
•
External interrupt
• Interrupt by edge detection (rising, falling, or both edges can be selected)
• Can be used to recover from low-power consumption (standby) modes.
•
8/10-bit A/D converter
• 8-bit or 10-bit resolution can be selected
•
Low-power consumption (standby) mode
• Stop mode
• Sleep mode
• Watch mode (for dual clock product)
• Timebase timer mode
•
I/O ports :
• The number of maximum ports
•
Single clock product : 54 ports
•
Dual clock product : 52 ports
• Port configuration
•
General-purpose I/O ports (N-ch open drain) : 6 ports
•
General-purpose I/O ports (CMOS)
: Single clock product : 48 ports
Dual clock product : 46 ports
•
Programmable input voltage levels of port
Automotive input level
/
CMOS input level
/
hysteresis input level
•
Flash memory security function
Protects the content of Flash memory (Flash memory device only)
2
DS07-12614-5E
MB95100AM Series
■
MEMORY LINEUP
Flash
MB95F104AMS/F104ANS/F104AJS
MB95F104AMW/F104ANW/F104AJW
MB95F106AMS/F106ANS/F106AJS
MB95F106AMW/F106ANW/F106AJW
MB95F108AMS/F108ANS/F108AJS
MB95F108AMW/F108ANW/F108AJW
16K bytes
32K bytes
60K bytes
RAM
512 bytes
1K byte
2K bytes
DS07-12614-5E
3
MB95100AM Series
■
PRODUCT LINEUP
Part number
MB95
108AM
Parameter
Type
MASK
ROM
product
MB95F
104AMS/
MB95F
106AMS/
MB95F
108AMS
MB95F
104ANS/
MB95F
106ANS/
MB95F
108ANS
MB95F
104AMW/
MB95F
106AMW/
MB95F
108AMW
MB95F
104ANW/
MB95F
106ANW/
MB95F
108ANW
MB95F
104AJS/
MB95F
106AJS/
MB95F
108AJS
MB95F
104AJW/
MB95F
106AJW/
MB95F
108AJW
Flash memory product
60 Kbytes (Max)
2 Kbytes (Max)
Yes
No
Dual clock
Single clock
Dual clock
ROM capacity*
1
RAM capacity*
1
Reset output
Clock system
Low voltage
detection reset
Clock supervisor
CPU functions
Selectable
single/dual
clock*
3
Yes/No
Option*
2
Single clock
No
Yes
No
No
Yes
Yes
Peripheral functions
Number of basic instructions
: 136
Instruction bit length
: 8 bits
Instruction length
: 1 to 3 bytes
Data bit length
: 1, 8, and 16 bits
Minimum instruction execution time : 61.5 ns (at machine clock frequency 16.25 MHz)
Interrupt processing time
: 0.6
μs
(at machine clock frequency 16.25 MHz)
•
Single clock product : 54 ports (N-ch open drain : 6 ports, CMOS : 48 ports)
•
Dual clock product : 52 ports (N-ch open drain : 6 ports, CMOS : 46 ports)
Programmable input voltage levels of port :
Automotive input level
/
CMOS input level
/
hysteresis input level
Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Reset generated cycle
At main oscillation clock 10 MHz
: Min 105 ms
At sub oscillation clock 32.768 kHz (for dual clock product) : Min 250 ms
Capable of replacing 3 bytes of ROM data
Master/slave sending and receiving
Bus error function and arbitration function
Detecting transmitting direction function
Start condition repeated generation and detection functions
Built-in wake-up function
Data transfer capable in UART/SIO
Full duplex double buffer, variable data length (5/6/7/8-bit), built-in baud rate generator
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected.
Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
(Continued)
General-pur-
pose I/O ports
Timebase timer
Watchdog timer
Wild register
I
2
C
UART/SIO
4
DS07-12614-5E
MB95100AM Series
Part number
MB95
108AM
Parameter
LIN-UART
MB95F
104AMS/
MB95F
106AMS/
MB95F
108AMS
MB95F
MB95F
MB95F
104ANS/ 104AMW/ 104ANW/
MB95F
MB95F
MB95F
106ANS/ 106AMW/ 106ANW/
MB95F
MB95F
MB95F
108ANS 108AMW 108ANW
MB95F
104AJS/
MB95F
106AJS/
MB95F
108AJS
MB95F
104AJW/
MB95F
106AJW/
MB95F
108AJW
Dedicated reload timer allowing a wide range of communication speeds to be set.
Full duplex double buffer
Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capa-
ble
LIN functions available as the LIN master or LIN slave.
8-bit or 10-bit resolution can be selected.
Two clock modes and two counter operating modes can be selected. Square wave-
form output
Count clock : 7 internal clocks and external clock can be selected.
Counter operating mode : reload mode or one-shot mode can be selected.
Each channel of the timer can be used as “8-bit timer
×
2 channels” or “16-bit timer
×
1 channel”.
Built-in timer function, PWC function, PWM function, capture function, and square
waveform output
Count clock : 7 internal clocks and external clock can be selected
PWM mode or one-shot mode can be selected.
Counter operating clock : 8 selectable clock sources
Support for external trigger start
Each channel of the PPG can be used as
“
8-bit PPG
×
2 channels
”
or
“
16-bit PPG
×
1 channel
”
.
Counter operating clock : Eight selectable clock sources
8/10-bit A/D converter
(12 channels)
16-bit reload timer
8/16-bit compound
timer (2 channels)
Peripheral functions
16-bit PPG
(2 channels)
8/16-bit PPG
(2 channels)
Watch counter
Count clock : 4 selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
(for dual clock product) Counter value can be set from 0 to 63. (Capable of counting for 1 minute when
selecting clock source 1 second and setting counter value to 60)
Watch prescaler
4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
(for dual clock product)
External interrupt
(12 channels)
Flash memory
Interrupt by edge detection (rising, falling, or both edges can be selected.)
Can be used to recover from standby modes.
Supports automatic programming, Embedded Algorithm
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Number of write/erase cycles (Minimum) : 10000 times
Data retention time : 20 years
Erase can be performed on each block
Block protection with external programming voltage
Flash Security Feature for protecting the content of the Flash
(MB95F108AMS/F108ANS/F108AJS/F108AMW/F108ANW/F108AJW only)
Sleep, stop, watch (for dual clock product) , and timebase timer
(Continued)
Standby mode
DS07-12614-5E
5
京公网安备 11010802033920号
EEWORLD
